10-14-2002
help installing Sun 8mm unipack scsi tape drive
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the tape is not found.
Whatever backup commands I issued such as mt, tar, or ufsdump, I would just get "/dev/rmt/0n no device or address" message.
Here are questions hoping you can help out:
1. do I need to do any configuration to prepare tape drive for use? such as mounting?
2. what other methods can I use to verify that the tape drive is recognized by O/S and ready to be used.
my system info:
Sun Ultra 5 running solaris 7
Thanks in advance for your help.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
2. UNIX for Dummies Questions & Answers
hello,
I don't know what exactly the cause and the solution!!
suddenly I receive this error message when I want to use the 8mm tape drive
"I/O write error"
I disconnect the tape drive and I hook it in another WS and I receive this error :- ... (5 Replies)
Discussion started by: geoquest
5 Replies
3. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
4. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
5. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
6. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
7. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
10. Solaris
Hi all,
this time I'd need a help from an advanced Solaris system admin :rolleyes:
I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all).
Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies
LEARN ABOUT CENTOS
tapeinfo
TAPEINFO(1) General Commands Manual TAPEINFO(1)
NAME
tapeinfo - report SCSI tape device info
SYNOPSIS
tapeinfo -f <scsi-generic-device>
DESCRIPTION
The tapeinfo command reads various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
issues raw commands directly to the tape drive, using either the operating system's SCSI generic device ( e.g. /dev/sg0 on Linux,
/dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.
One good time to use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
'tapeinfo' will report a more exact description of what went wrong.
Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.
OPTIONS
The first argument, given following -f , is the SCSI generic device corresponding to your tape drive. Consult your operating system's doc-
umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).
Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls them. Under Linux,
"cat /proc/scsi/scsi" will tell you what SCSI devices you have.
BUGS AND LIMITATIONS
This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).
AVAILABILITY
tapeinfo is currently being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of programs. The
'mtx' home page is http://mtx.sourceforge.net and the actual code is currently available there and via SVN from http://source-
forge.net/projects/mtx.
SEE ALSO
mt(1),mtx(1),scsitape(1),scsieject(1),loaderinfo(1)
TAPEINFO1.0 TAPEINFO(1)