Sponsored Content
Top Forums UNIX for Advanced & Expert Users Trying to get my USB network card to work with Linux Post 28941 by amicrawler2000 on Thursday 26th of September 2002 03:15:15 PM
Old 09-26-2002
ok

well it depends on what unix you use bsd linux true64 bla bla
and unix will probe it you need to tell it what to do

i find that if i got to my control panel and goto the usb driver and add them the system will see it i added a new video card and usb dev to it a worked like magic but i use Iris,Lycrios you can get any unix linux os here @ ftp.bendug.org/pub/

good luck
amicrawler2000
 

9 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Network Card Problem On Linux

Hi I just installed linux red hat 7.0 and i can't connect the machine on the network. Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize. Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

sound card doesn't work!

Hello I have just installed Free BSD on my old computer system to learn how to use it and I can't get any sound. When I start KDE desktop I receve a message that says "Sound server informational message: Error while initializing the sound driver: device /dev/dsp can't be opened (No such file... (1 Reply)
Discussion started by: ac101
1 Replies

5. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

6. Solaris

usb memory card

I just got a removable memory card. I tried the following bu still my OS solaris x86 cannot detect it and also i got an error touch /reconfigure init 0 I inserted the removable memory card and the powered the system on I got the following on at boot up when i fully logged in I did ... (2 Replies)
Discussion started by: seyiisq
2 Replies

7. Solaris

solaris ethernet card and mounting usb drives

I had installed soalris 10 on my dell vostro 1400.It had installed succefully. If i type ifconfig -a it is showing only my loop back adpater. So how to tell me how to mount my usb drive and how to configure my lan ethernet card,My lan ethernet card is Broadcom. Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies

8. UNIX for Dummies Questions & Answers

USB-USB cable between linux and windows computers

Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive. Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies

9. Red Hat

Linux Red Hat AS3 Network card is not detecting ...

Dear Expert, I 've installed Redhat linux AS3, My machine having Inbuild network card (Intel(R) 82566DM-2 Gigabit Network Connection). I've downloaded e1000e-2.3.2 from Intel site, but its not working for my machine. I'm unable to configure the Network. ifconfig eth0 xx.xx.xx.xx netmask... (0 Replies)
Discussion started by: Mohammed Faiz
0 Replies
CARD(1)                                                                 FSF                                                                CARD(1)

NAME
card - print reference card of program options SYNOPSIS
card [OPTION]... PROGRAM... DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help. OPTIONS
-h, --help display this help and exit -v, --version display version information and exit -o, --output=FILE save the output in FILE -l, --language=LL print the help in the language LL (default: English) --command=CMD perform pretty-printing on the output of CMD (e.g. --command='netscape -help') Options for a2ps are given after `--', for instance $ card -lfr a2ps -- -Pdisplay -4 News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/ AUTHOR
Written by Akim Demaille. REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>. COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1). The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the command info card should give you access to the complete manual. card 1.3 (GNU a2ps 4.14) March 2014 CARD(1)
All times are GMT -4. The time now is 08:53 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy