08-20-2002
Installing network card
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
4. Solaris
I need to install a driver for my RT2500 PCI wireless network card on my Solaris 10.
So I went to the ralink website (the manufacturer of the network card), and downloaded the linux (well supposedly the unix driver) binary file. Burned it to dvd, and copied from the dvd to my solaris computer.... (3 Replies)
Discussion started by: Xannen
3 Replies
5. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT REDHAT
dummy_cs
DUMMY_CS(4) Kernel Interfaces Manual DUMMY_CS(4)
NAME
dummy_cs - PCMCIA dummy device driver
SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...]
DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and
the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO
card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set-
ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers.
It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of
the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to
ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions
about card types, it is forced to rely on the card information, for better or worse.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
free_ports=n
A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy
driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)