06-11-2002
According to the FAQ on slackware:
How do I add X to this?
Assuming you've got the space to install it, download the X packages (the files ending in .tgz) from this directory:
ftp://ftp.slackware.com/pub/slackwar...e/slakware/x1/
You might also grab the diskx1 file, which describes each of the packages. You can save disk space if you don't install all of the X servers (you only need the one for your video card), and you might also leave out extra fonts, old X shared libraries (oldlibs*.tgz), and possibly development tools if you're not planning to compile X software yourself. Once you've collected the packages you plan to install into a directory, run this to install them:
installpkg *.tgz
Before running X, you'll need to set it up with 'xf86config'.
Found at slackware.org
9 More Discussions You Might Find Interesting
1. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
2. Solaris
hi there,
i'm quite new to solaris and recently i've bought a ibm thinkpad...
now i intend to install a dual-boot system. in fact i've got it managed to install the end-user system
with dual-boot working. apart from following issue other devices got recognized...
this is what i've found out... (2 Replies)
Discussion started by: pseudocoder
2 Replies
3. Linux
Hello all,
I need to develop an application that would be used as a simulator to test various custom algorithms. As I have never embarked on this kind of work, I need some advice:
1. Which GUI library to use in Linux, GTK+ or FLTK? The simulator application needs to output various... (2 Replies)
Discussion started by: fox_hound_33
2 Replies
4. Slackware
Hi Guys,
I'm trying to install slackware 10.2 on a on compaq laptop with Sansung
HM121HI hard drive but I wonder what kernel should I use so it can recognize the had disk. Initially I've tried using sata.i and then try to use the fdisk utility to create the new partiotions but doesn't seem... (0 Replies)
Discussion started by: hariza
0 Replies
5. UNIX for Dummies Questions & Answers
Hi gurus,
I am trying to connect to wifi access point with terminal, I set up my own access point (no encryption or MAC filters)
I ran followings commands
$ sudo iwlist eth1 scanning
eth1 Scan completed :
Cell 01 - Address: 00:11:2F:A2:99:1C
... (1 Reply)
Discussion started by: wakatana
1 Replies
6. Hardware
Hello everybody,
I'm having troubles with Slackware 13.1 and network cards.
I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies
7. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
8. Ubuntu
Is it possible to install Ubuntu 11.04 or Ubuntu 11.10 in Lenovo Thinkpad E520-1143 Now it Powerd By windowd Xp Professional is it possible to install Ubuntu in it and supports all drivers for ma laptop such as VGA driver Sound,Wireless,Lan , fingerprint,camera pls reply r is it possible to... (0 Replies)
Discussion started by: babinlonston
0 Replies
9. Red Hat
Hi All,
I have a Thinkpad - T430, which is having the wireless card as "03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205".
This one i need to configure as wifi hotspot. which i believe need to configure hostapd.conf, this kind of configuration is new to me anybody done... (1 Reply)
Discussion started by: linux.amrit
1 Replies
LEARN ABOUT DEBIAN
linux::distribution
Linux::Distribution(3pm) User Contributed Perl Documentation Linux::Distribution(3pm)
NAME
Linux::Distribution - Perl extension to detect on which Linux distribution we are running.
SYNOPSIS
use Linux::Distribution qw(distribution_name distribution_version);
if(my $distro = distribution_name) {
my $version = distribution_version();
print "you are running $distro, version $version
";
} else {
print "distribution unknown
";
}
Or else do it OO:
use Linux::Distribution qw(distribution_name distribution_version);
my $linux = Linux::Distribution->new;
if(my $distro = $linux->distribution_name()) {
my $version = $linux->distribution_version();
print "you are running $distro, version $version
";
} else {
print "distribution unknown
";
}
DESCRIPTION
This is a simple module that tries to guess on what linux distribution we are running by looking for release's files in /etc. It now looks
for 'lsb-release' first as that should be the most correct and adds ubuntu support. Secondly, it will look for the distro specific files.
It currently recognizes slackware, debian, suse, fedora, redhat, turbolinux, yellowdog, knoppix, mandrake, conectiva, immunix, tinysofa,
va-linux, trustix, adamantix, yoper, arch-linux, libranet, gentoo, ubuntu, scientific, oracle enterprise linux and redflag.
It has function to get the version for debian, suse, fedora, redhat, gentoo, slackware, scientific, oracle enterprise linux, redflag and
ubuntu(lsb). People running unsupported distro's are greatly encouraged to submit patches :-)
EXPORT
None by default.
TODO
Add the capability of recognize the version of the distribution for all recognized distributions.
AUTHORS
Alexandr Ciornii <alexchorny@gmail.com>, <http://chorny.net> Alberto Re, <alberto@accidia.net> Judith Lebzelter, <judith@osdl.org>
COPYRIGHT AND LICENSE
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself, either Perl version 5.8.5 or,
at your option, any later version of Perl 5 you may have available.
perl v5.14.2 2012-03-18 Linux::Distribution(3pm)