Sponsored Content
Full Discussion: Ethernet
Top Forums UNIX for Dummies Questions & Answers Ethernet Post 20316 by PxT on Wednesday 24th of April 2002 01:42:02 PM
Old 04-24-2002
Quote:
Originally posted by Kelam_Magnus

Neo, can you or someone please merge this with the original post from the other day?

Done! Smilie



Please tell us what version of Linux you are running, and from which vendor. RedHat keeps its network configuration files in /etc/sysconfig/network-scripts. Other vendors may be slightly different.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies

2. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies

3. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies

4. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

5. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies

6. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies

7. Solaris

ethernet

my solris box network is unreachable how to solve this ipaddress assiagning and entry in vi /etc/host how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
WIRELESS(7)						     Linux Programmer's Manual						       WIRELESS(7)

NAME
wireless - Wireless Tools and Wireless Extensions SYNOPSIS
iwconfig iwpriv -a DESCRIPTION
The Wireless Extensions is an API allowing you manipulate Wireless LAN networking interfaces. It is composed of a variety of tools and configuration files. It is documented in more detail in the Linux Wireless LAN Howto. The Wireless Tools are used to change the configuration of wireless LAN networking interfaces on the fly, to get their current configura- tion, to get statistics and diagnose them. They are described in their own man page, see below for references. Wireless configuration is specific to each Linux distribution. This man page will contain in the future the configuration procedure for a few common distributions. For the time being, check the file DISTRIBUTIONS.txt included with the Wireless Tools package. DEBIAN 3.0 In Debian 3.0 (and later) you can configure wireless LAN networking devices using the network configuration tool ifupdown(8). File : /etc/network/interfaces Form : wireless-<function> <value> wireless-essid Home wireless-mode Ad-Hoc See also : /etc/network/if-pre-up.d/wireless-tools /usr/share/doc/wireless-tools/README.Debian SuSE 8.0 SuSE 8.0 (and later) has integrated wireless configuration in their network scripts. Tool : Yast2 File : /etc/sysconfig/network/wireless /etc/sysconfig/network/ifcfg-* Form : WIRELESS_<function>=<value> WIRELESS_ESSID="Home" WIRELESS_MODE=Ad-Hoc See also : man ifup info scpm ORIGINAL PCMCIA SCRIPTS
If you are using the original configuration scripts from the Pcmcia package, you can use this method. File : /etc/pcmcia/wireless.opts Form : *,*,*,*) ESSID="Home" MODE="Ad-Hoc" ;; See also : /etc/pcmcia/wireless File PCMCIA.txt part of Wireless Tools package AUTHOR
Jean Tourrilhes - jt@hpl.hp.com http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/ SEE ALSO
iwconfig(8), iwlist(8), iwspy(8), iwpriv(8), iwevent(8). wireless-tools 4 March 2004 WIRELESS(7)
All times are GMT -4. The time now is 06:04 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy