Ethernet Post: 20312

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by...

2. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the...

3. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up?

4. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

5. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses...

6. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ...

7. Solaris

ethernet

my solris box network is unreachable how to solve this ipaddress assiagning and entry in vi /etc/host how to solve network is unreachable

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

LEARN ABOUT OPENSOLARIS

ethers

ethers(4)							   File Formats 							 ethers(4)

NAME

       ethers - Ethernet address to hostname database or domain

DESCRIPTION

       The  ethers  file  is  a local source of information about the (48-bit) Ethernet addresses of hosts on the Internet. The ethers file can be
       used in conjunction with or instead of other ethers sources, including the NIS maps ethers.byname and ethers.byaddr, the NIS+ table ethers,
       or Ethernet address data stored on an LDAP server. Programs use the ethers(3SOCKET) routines to access this information.

       The ethers file has one line for each host on an Ethernet. The line has the following format:

       Ethernet-address official-host-name

       Items are separated by any number of SPACE and/or TAB characters. A `#' indicates the beginning of a comment extending to the end of line.

       The  standard  form  for  Ethernet  addresses is "x:x:x:x:x:x" where x is a hexadecimal number between 0 and ff, representing one byte. The
       address bytes are always in network order. Host names may contain any printable character other than SPACE, TAB, NEWLINE, or comment  char-
       acter.

FILES

       /etc/ethers

SEE ALSO

       ethers(3SOCKET), hosts(4), nsswitch.conf(4)

SunOS 5.11							    22 Jul 2004 							 ethers(4)