Sponsored Content
Top Forums UNIX for Dummies Questions & Answers aggregate ethernet ports under Solaris Post 15280 by 98_1LE on Tuesday 12th of February 2002 02:30:51 PM
Old 02-12-2002
Thanks for the good info Smilie
 

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. Solaris

[Please Help] ethernet problem on solaris

Hi All, i have a problem with my database server using sun machine v440 and sunOS 5.9 on ethernet, i've checked on system log /var/adm/messages and found much error messages like shown below : Sep 21 16:14:48 dbs genunix: WARNING: ce0: fault detected external to device; service degraded Sep... (2 Replies)
Discussion started by: bucci
2 Replies

4. Solaris

Configuring TP Ethernet in SPARCstation 5 Solaris 8

Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Discussion started by: mads-nielsen
4 Replies

5. UNIX for Dummies Questions & Answers

NTP idle ports and ethernet interfaces

I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client. Thank you. *.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies

7. Solaris

IPMP over aggregate in Solaris 11

hi all, i start with solaris 11 and i am disapointed by the change on ip managing. i want to set a ipmp over tow aggregate but i dont find any doc and i am lost with the new commande switch1 net0 aggregate1 | net1 aggregate1 |-----| |... (1 Reply)
Discussion started by: sylvain
1 Replies

8. AIX

Locating and Mapping Physical Ethernet Ports

Hello Everyone, Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ? Server with expansion box has around 12 ethernet ports (fibre and ethernet) what is the quickest way to map or find out en0 represents which physical port ? ... (1 Reply)
Discussion started by: filosophizer
1 Replies

9. Solaris

Solaris 11 ssh on machine with multiple Ethernet ports

I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs. I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are net0 192.168.1.82 net1 192.168.2.82 and so on till net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
INFO(5) 							File Formats Manual							   INFO(5)

NAME
info - readable online documentation DESCRIPTION
The Info file format is an easily-parsable representation for online documents. It can be read by emacs(1) and info(1) among other pro- grams. Info files are usually created from texinfo(5) sources by makeinfo(1), but can be created from scratch if so desired. For a full description of the Texinfo language and associated tools, please see the Texinfo manual (written in Texinfo itself). Most likely, running this command from your shell: info texinfo or this key sequence from inside Emacs: M-x info RET m texinfo RET will get you there. AVAILABILITY
http://www.gnu.org/software/texinfo/ REPORTING BUGS
Please send bug reports to bug-texinfo@gnu.org, general questions and discussion to help-texinfo@gnu.org. SEE ALSO
info(1), install-info(1), makeinfo(1), texi2dvi(1), texindex(1). emacs(1), tex(1). texinfo(5). FSF
GNU Info INFO(5)
All times are GMT -4. The time now is 04:28 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy