02-05-2002
thanx
i found the file in /etc/sysconfig/networking/devices/ifcfg-eth0
and here i can add the new ip and after reboot everything is ok.
but i don't know how i can have it changed without rebooting and
more important that that i want to add more than one ip for this
interface.
Can anyone help me up?
10 More Discussions You Might Find Interesting
1. Linux
Had problems in configuring USB memory stick in RHL 9.
Please assist.
With regards,
Kungra. (1 Reply)
Discussion started by: kungra2006
1 Replies
2. Shell Programming and Scripting
Hi,
I want to configure 2-gateways in Linux .
Please tell me how I can achieve this. I am accesing 2-internet
connection through these 2-gateways. So I am looking that
if 1-gets down then also other one is working.
Regards
JAGDISH (1 Reply)
Discussion started by: jagdish.machhi@
1 Replies
3. Solaris
hi friends,
I have brand new Sun Ultra 20 WS installed.
It was preinstalled with Solaris 10 6/06 system,
in ifconfig -a command only loop back intervace is showing.
and
/etc/path_to_install also not able to find the interface name.
my questions are:
1. Is there any command to get... (1 Reply)
Discussion started by: subhankar
1 Replies
4. Red Hat
Hi All
when I give the command,
$ ping <hostname>
I get the following error
ping: unknown host <hostname>
I have checked in the following files,
/etc/sysconfig/network
/etc/hosts
/etc/resolv.conf
/etc/nsswitch.conf
Every where in these files host name and IP address are given... (2 Replies)
Discussion started by: nagapradeep
2 Replies
5. AIX
I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8.
when I run the command
lsattr -El ent8
I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But... (10 Replies)
Discussion started by: thenomad
10 Replies
6. UNIX for Advanced & Expert Users
Can anybody please explain the below table to monitor NTP daemon status
This contains many columns like remote,refid,st....various values corresponding to those columns
If possible provide me any link to study about these quantities clearly.
It is very much required for my project please... (3 Replies)
Discussion started by: sgand
3 Replies
7. IP Networking
i have a linux server runnig oracle applications.
i need to access this server from putty using ssh through internet.
i did by registering my static ip with the dnydns.org and i am able to connect to the server.
but now there is no security to authenticate any user as any one knowing the... (6 Replies)
Discussion started by: u.n.i.x
6 Replies
8. Infrastructure Monitoring
I am trying to enabling SNMP access and trap forwarding for Linux(RHEL5) using following official url from IBM.
http://publib.boulder.ibm.com/infocenter/eserver/v1r2/index.jsp?topic=/diricinfo/fqm0_t_enabling_snmp_access_and_trap_forwarding_for_linux.html
In my system, snmp and snmplibs are... (1 Reply)
Discussion started by: SiddhV
1 Replies
9. IP Networking
Can someone help with a detail step-by-step oh how to configure DNS server on Linux Server.
-
I need to have 3 IP addresses map to a single hostname.
for clients
I'm a Linux rookie.
Thanks
Oscar (1 Reply)
Discussion started by: FrankOscar
1 Replies
10. Red Hat
Dear Experts,
We have requirement to configure Dot matrix printer in linux, Also need to register in Oracle application R12.0.6 version where i need get the print in landscape format.
Request you all kindly help on the same.
Thank you,
Alone.
---------- Post updated 02-18-14 at 01:02... (6 Replies)
Discussion started by: Alone
6 Replies
LEARN ABOUT SUSE
ifcfg-vlan
IFCFG-VLAN(5) Network configuration IFCFG-VLAN(5)
NAME
ifcfg-vlan - virtual LAN interface configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-vlan*
Virtual LANs (802.1q)
To setup a vlan interface you need a configuration file that contains at least the mandatory
ETHERDEVICE
variable with the real interface used for the virtual LAN.
Further, it may contain the optional
VLAN_ID
variable that specifies the VLAN ID.
By default and when the VLAN_ID variable is not set, the number at the end of the interface name is the VLAN ID.
Preferably the interface name and the configuration file follow the VLAN interface name scheme (type), that is either:
ifcfg-vlan<VLAN-ID> (e.g. ifcfg-vlan42)
or
ifcfg-name.<VLAN-ID> (e.g. ifcfg-eth0.42)
The VLAN-ID can be also 0-padded (e.g. ifcfg-vlan0042 or ifcfg-eth0.0042).
Also in case of custom names, trailing digits are interpreted as VLAN-ID by default (e.g. ifcfg-dmz42). When VLAN_ID is set in the config,
the interface name have any name (e.g. ifcfg-foobar).
Note: The drawback of custom interface names and VLAN_ID usage is, that a rename of the interface is required and that they violate the
name scheme.
The real interface will be set UP automatically and doesn't need a config file in case of a physical interface. But without a config file
YaST will consider this interface as unused, if will not follow hotplug events and you're unable to apply any settings, e.g. ETH-
TOOL_OPTIONS. To avoid that, provide an config file with at least STARTMODE='auto'.
The rest of the VLAN interface IP and routes configuration do not differ from ordinary interfaces. See also man ifcfg and man routes for
details.
EXAMPLES
Sets up vlan3 vlan interface on top of eth0:
ifcfg-vlan3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up eth0.3 vlan interface on top of eth0:
ifcfg-eth0.3
STARTMODE='auto'
ETHERDEVICE='eth0'
IPADDR='192.168.3.27/24'
Sets up lan1 vlan interface with ID 42 on top of eth0:
ifcfg-lan1
STARTMODE='auto'
ETHERDEVICE='eth0'
VLAN_ID='42'
IPADDR='192.168.3.27/24'
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de>
Michal Svec <msvec@suse.cz>
Bjoern Jacke
Mads Martin Joergensen <mmj@suse.de>
Michal Ludvig <mludvig@suse.cz>
Marius Tomaschewski <mt@suse.de>
SEE ALSO
routes(5), ifcfg(5), ifup(8).
sysconfig August 2004 IFCFG-VLAN(5)