12-05-2001
10 More Discussions You Might Find Interesting
1. Solaris
Can someone tell me what the following means? We have a v440 running Solaris 9. What do the patterns actually mean?
May 17 12:12:03 ibasdb02 cediag: Revision: 1.78 @ 2005/02/11 15:5
:29 UTC
May 17 12:12:03 ibasdb02 cediag: Analysed System: SunOS 5.9 with
UP 117171-17 (MPR active)
May 17... (5 Replies)
Discussion started by: hshapiro
5 Replies
2. UNIX for Advanced & Expert Users
I have worked with Qlogic (Sun) fiber cards a lot and with Emulex fiber cards only a little. Here is the scenario: I have a Sun 490 with 3 Emulex cards in it. A pair are for the 6120 array that is attached, the other is a direct attach so our SAN for Veritas Netbackup to back up the system.I... (0 Replies)
Discussion started by: lm_admin_dh
0 Replies
3. Solaris
Dear All
I would Like to know that if suppose c1t0d0 is of 72 gb hard disk and system boot from this hard disk and c1t1d0 is of 147gb hard disk. Can we implement hardware raid (Mirror) between these two hard disks of different capacity if raid crontroller is present in the server
Kind regards (4 Replies)
Discussion started by: girish.batra
4 Replies
4. Solaris
Hi
I am right now facing a strange hardware problem. System get booted with the following error:
Fatal Error Reset
CPU 0000.0000.0000.0003 AFSR 0100.0000.0000.0000 SCE
AFAR 0000.07c6.0000.1000
SC Alert: Host System has Reset
It happen 4 or 5 times and get the same error every time.I... (8 Replies)
Discussion started by: girish.batra
8 Replies
5. Linux
Hey guys how to do diagnose Linux for hardware problems/issues. This is a general question for all common hardware components under Linux server. (1 Reply)
Discussion started by: sbn
1 Replies
6. Solaris
Hey guys how to do diagnose solaris for hardware problems/issues. This is a general question for all common hardware components under solaris server. (4 Replies)
Discussion started by: sbn
4 Replies
7. HP-UX
Hey guys how to do diagnose HP-UX for hardware problems/issues. This is a general question for all common hardware components under HP-UX server. (4 Replies)
Discussion started by: sbn
4 Replies
8. BSD
Hi there. I have an old laptop Toshiba Tecra 510 (P1, 147MB RAM, 30GB HDD) and I installed FreeBSD 7.2.
For networking I have a PCMCIA card for wired network. The problem is that I cannot start and run PCMCIA
As I know in Linux there is a tool pcmciautils for this pc-cards, but in FreeBSD I have... (1 Reply)
Discussion started by: hirohitosan
1 Replies
9. Solaris
First of all it's shut down 60 second after power on and write on console :
SC Alert: Correct SCC not replaced - shutting managed system down!
This is cured by moving out battery from ALOM card.
Now server start to loop during the testing.
That's on the console:
>@(#) Sun Fire V440,Netra... (14 Replies)
Discussion started by: Alisher
14 Replies
10. Solaris
Dear:
the Cureent PC Dell GX620
the Current Hardware
4 GB ram
80 HDD
what i do
remove old 4GB ram and install 8 GB
remove old HDD and install new on 160GB
try to install the Unix Sun Solaris
after booting and when arrive to step which i should select interactive
error meg... (7 Replies)
Discussion started by: hosney00ux
7 Replies
LEARN ABOUT REDHAT
dummy_cs
DUMMY_CS(4) Kernel Interfaces Manual DUMMY_CS(4)
NAME
dummy_cs - PCMCIA dummy device driver
SYNOPSIS
insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...]
DESCRIPTION
The dummy_cs module has two purposes. It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and
the source code is heavily commented. It is also written to function as a sort of generic ``point enabler'': when bound to any PCMCIA IO
card, it will read the card's Configuration Information Structure, and configure the card appropriately. The configuration includes set-
ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers.
It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and the complexity of
the data format. A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to
ensure that the on-card information is complete. Thus, the dummy_cs module is limited by its generality: since it makes no assumptions
about card types, it is forced to rely on the card information, for better or worse.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
free_ports=n
A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps. This is useful if the dummy
driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver. The default is 0 (false).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:47 DUMMY_CS(4)