Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Adding an interface to solaris? Post 1045 by 98_1LE on Tuesday 6th of February 2001 10:22:21 AM
Old 02-06-2001
I beleivethat ifconfig -a only shows configured interfaces. Though I am not certain that this will work, try creating a file named /etc/hostname.qe3 containing the hostname of that interface. (This assumes that qe0,qe1 & qe2 are present) Use ifconfig to give it an IP and add the entry to /etc/hosts.
 

8 More Discussions You Might Find Interesting

1. HP-UX

Adding virtual Interface on HP UX

Hello all, I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box. I know that ifconfig can be used to add the Virtual interface. BUt i do not know the exact syntax. it some times gives plumb error if i try to add # ifconfig vif0 10.1.10.1 up plumb error: No such file... (3 Replies)
Discussion started by: supersumanth
3 Replies

2. IP Networking

Activating an interface on a Solaris 10

Help! How do I get (configure) an inteface up in order to get access to the internet? System in use is SPARC Ultra 5 - it worked before but not now when I re-installed the system and forgot to connect the RJ45 cable to the interface. (3 Replies)
Discussion started by: Maen
3 Replies

3. Solaris

Adding Loopback Interface

Hello, I have a SunOS (5.5.1) system that I need to migrate to a new IP address. I would like to have any requests destined for the old IP to be forwarded to this server. One suggestion I had was to add a route on my router that would point the old IP to the new IP. How do I add another... (2 Replies)
Discussion started by: reiklen
2 Replies

4. Solaris

sppp0 interface in solaris 10

What is sppp0 interface in solaris 10 and how can we disable it ? (1 Reply)
Discussion started by: fugitive
1 Replies

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

6. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

7. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
nca.if(4)							   File Formats 							 nca.if(4)

NAME
nca.if - the NCA configuration file that specifies physical interfaces SYNOPSIS
/etc/nca/nca.if DESCRIPTION
Specify the physical interfaces for which the Solaris Network Cache and Accelerator ("NCA") feature will be configured in the nca.if con- figuration file. List the physical interfaces in the file, one per line. To configure NCA to listen on all physical interfaces present on the system backed by a hostname.{interface_name}, then list only an asterik ("*") in nca.if. When the ncakmod(1) initialization script is invoked during system boot, it will attempt to configure each physical interface specified in the nca.if file by using ncaconfd(1M). Note that there must be an accompanying hostname.{interface_name} file and an entry in /etc/hosts for the contents of hostname.{interface_name}. You must reboot in order to implement changes to the nca.if file. EXAMPLES
x86 Example 1: nca.if on x86 The following is an example of an nca.if file that would be used on an x86 system: iprb1 iprb6 iprb8 SPARC Example 2: nca.if on SPARC The following is an example of an nca.if file that would be used on a SPARC system: hme2 hme3 hme4 All Platforms Example 3: Configuring NCA to Listen on All Physical Interfaces The following example shows the contents of an nca.if file that would be used to configure either platform to listen on all physical inter- faces present on the system: * FILES
/etc/nca/nca.if Lists the physical interfaces on which NCA will run. /etc/hostname.{}{0-9} Lists all physical interfaces configured on the server. /etc/hosts Lists all host names associated with the server. Entries in this file must match with entries in /etc/host- name.{}{0-9} for NCA to function. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWncar | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
nca(1), ncab2clf(1), ncakmod(1), ifconfig(1M), ncakmod.conf(4), ncalogd.conf(4), attributes(5) System Administration Guide: IP Services SunOS 5.10 18 Feb 2003 nca.if(4)
All times are GMT -4. The time now is 03:44 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy