10 More Discussions You Might Find Interesting
1. SCO
Hi,
I am using SCO OpenServer 5
During boot I get this message:
PANIC: HTFS: Bad directory ino 2 (offset 0) on HTFS dev hd (1/42)
Cannot dump 8095 pages to dumpdev hd (1/41): Space for only 0 pages
Dump not completed
How can I fix this? I have no boot/root floppy.
If it is a "disk... (8 Replies)
Discussion started by: nubian_sundance
8 Replies
2. Solaris
In the server room at my new job, there is a V100 with a problem. When power is turned on, the machine goes to the lom prompt. Entering poweron yields an endless supply of this message with no way to break out of it.
**********************************************
PSTATE=0000000000000015... (3 Replies)
Discussion started by: chilinski
3 Replies
3. Solaris
Hi all,
please i need your help urgently
I am faced to a serious boot disks issue on an Sun Fire E2900.
The system run with two disque in zpool .
The operating system is Solaris 10 (ZFS)
The first time the issue occured, i got the error below on the two disks:
Apr 7 08:04:33... (0 Replies)
Discussion started by: saki_jumeau
0 Replies
4. Solaris
Hi all
i have an issue
when i change auto-boot?=false and reboot it
again it is going to auto-boot?=true
can any one tell that
what should i do for auto-boot?=false for permanently
thank you in advance (11 Replies)
Discussion started by: wkbn86
11 Replies
5. Red Hat
Hi,
I have a laptop with two os running in it, Windows XP & RHEL5. Accidentally, we have deleted the windows entry in grub.conf file. Later we connected the hard disk of laptop to another system & deleted the linux partitions from the disk management tool of windows.
Now the issue is, the... (7 Replies)
Discussion started by: Amol21
7 Replies
6. Solaris
Machine: x86
OS : Dualboot Solaris and RHEL5 -Solaris 10 in first fdisk partition.
RHEL5 - /boot in partition2
/ in partition3
swap in 1st... (1 Reply)
Discussion started by: saagar
1 Replies
7. Solaris
I had logged into Server via ALOM and was placed into runlevel 5 other than 3 which is default.
I did a svcadm delete boot-archive, and was promptly placed in runlevel 3.
Now, I am unable to do a telnet or login into the server through any other service.
bash-3.00# svcs -a
svcs -a
STATE ... (3 Replies)
Discussion started by: praveenr
3 Replies
8. HP-UX
Hello, have HP Visualize C3600 workstation. Issue is as follows:
When I attempt to boot, unit will not boot successfully and will halt at a menu, the same menu as when during a boot one hits any key within 10 seconds to discontinue. When I attempt to boot with Boot primary, both with IPL... (17 Replies)
Discussion started by: davel1000
17 Replies
9. HP-UX
Hi,all:
I want to boot an IA unix box from network, I am sure I set the DHCP and boot server, but it still failed !
It says : Client MAC Address: 00 18 FE 28 91 82 .....-
PXE-E16: Valid PXE offer not received.
Load of Core LAN Gb A failed: Not Found
I use the nettl command to trace the UDP... (0 Replies)
Discussion started by: bluepluto
0 Replies
10. UNIX for Advanced & Expert Users
Hi All,
1st HDD is loaded with Windows 2000 Professional and I have installed Red Hat ES 3.0 on second HDD(80GB). After linux installation failed to load windows and boot stucks with displaying only L How to fix this issue
Thanks in advance for your valuable answer.
Regards,
Bachegowda (1 Reply)
Discussion started by: bache_gowda
1 Replies
REBOOT(2) System Calls Manual REBOOT(2)
NAME
reboot - close down the system or reboot
SYNTAX
#define _MINIX_SOURCE 1
#include <unistd.h>
int reboot(int how, ...)
DESCRIPTION
Reboot() is used to close down the system. It allows several ways of shutting down depending on how:
reboot(RBT_HALT)
Halt the system and return to the monitor prompt.
reboot(RBT_REBOOT)
Reboot the system by letting the monitor execute the "boot" command.
reboot(RBT_PANIC)
Cause a system panic. This is not normally done from user mode, but by servers using the sys_abort() kernel call.
reboot(RBT_MONITOR, code, length)
Halt the system and let the monitor execute the given code of the given length. (code is of type char * and length of type size_t.)
reboot(RBT_RESET)
Reboot the system with a hardware reset.
Reboot() may only be executed by the super-user.
DIAGNOSTICS
If the call succeeds, it never returns. If something went wrong, the return value is -1 and an error is indicated by errno.
SEE ALSO
shutdown(8), reboot(8), halt(8), sync(1).
NOTES
Minix can not return to the monitor if running in real mode, or if started from MS-DOS. This means that most of the reboot functions will
change to a reset.
AUTHOR
Edvard Tuinder (v892231@si.hhs.NL)
REBOOT(2)