10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
I have a Linux server with a cifsmount, the entry in /etc/fstab looks like this: //windows_server_name/xyz /opt/xyz cifs credentials=/etc/creds/xyz.creds,uid=abc,gid=abc,noserverino,directio,_netdev 0 0
The username and password are stored in /etc/creds/xyz.creds
This works fine.:wall: How... (1 Reply)
Discussion started by: Joke Holmer
1 Replies
2. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
3. Ubuntu
Is there any way to compile smbfs module in kernel 3.10 running Ubuntu 12.04 LTS. I did a 'make menuconfig' and it shows cifs. I found out online that smbfs is deprecated and replaced by cifs. I have an old system with kernel version 2.4 which only has smbfs (no cifs). Is it possible to compile... (1 Reply)
Discussion started by: Monil
1 Replies
4. Solaris
Hi,
I am running into a some problems creating a dual boot system of 2 solaris instances using ZFS file system and I was wondering if someone can help me out.
First some back ground. I have been asked to change the file system of our server from UFS to ZFS. Currently we are using Solaris... (3 Replies)
Discussion started by: estammis
3 Replies
5. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
6. Solaris
Hi friends
I'm a newbie trying to automount a nfs shared directory. Below is the configuration I'm using
FreeBSD machine as NFS server. IP Address - 192.168.1.60
# cat /etc/exports
/shared 192.168.1.50
Solaris 10 as NFS client. IP Address - 192.168.1.50
# cat... (1 Reply)
Discussion started by: pankajj
1 Replies
7. UNIX for Advanced & Expert Users
I am having trouble mounting with cifs, but mounting the exact same command with smbfs works fine. The share is on another samba server and is set to full public guest access. # mount -t cifs //servername/sharename /mnt/temp -o password=""
mount error 13 = Permission denied Refer to the... (3 Replies)
Discussion started by: humbletech99
3 Replies
8. Solaris
Hi all ,
I am trying to isntallsolaris 10 using a DVD , But when i try to boot from the OB Prompt i am getting this error :
Rebooting with command: boot cdrom -install
Boot device: /pci@1f,700000/pci@0/pci@1/pci@0/ide@1f/cdrom@0,0:f File and args: -install
Can't read disk label.
Can't open... (2 Replies)
Discussion started by: ppass
2 Replies
9. Solaris
Hi,
I set up a RAID 5 configuration and for some reason the volumes won't mount when the system boots. I have to manually mount them from the command line and all is fine.
Here's the vfstab entries:
#device device mount FS fsck mount mount
#to mount ... (2 Replies)
Discussion started by: rpollard001
2 Replies
10. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
RUMP_SMBFS(8) BSD System Manager's Manual RUMP_SMBFS(8)
NAME
rump_smbfs -- mount a smbfs share with a userspace server
SYNOPSIS
file-system PUFFS
pseudo-device putter
rump_smbfs [options] share mountpoint
DESCRIPTION
NOTE! This manual page describes features specific to the rump(3) file server. Please see mount_smbfs(8) for a full description of the
available command line options.
The rump_smbfs utility can be used to mount smbfs file systems. It uses rump(3) and p2k(3) to facilitate running the file system as a server
in userspace. As opposed to mount_smbfs(8), rump_smbfs does not use file system code within the kernel and therefore does not require kernel
support except puffs(4). Apart from a minor speed penalty there is no downside with respect to in-kernel code.
Even though the rump_smbfs file system client runs within a virtual rump kernel in userspace, it uses host network services (by means of
``rump sockin''). This means that regardless of whether using rump_smbfs or mount_smbfs(8), the same network configurations will be used.
Currently, ``sockin'' supports IPv4.
To use rump_smbfs via mount(8), the flags -o rump and -t smbfs should be given. Similarly, rump_smbfs is used instead of mount_smbfs(8) if
``rump'' is added to the options field of fstab(5).
SEE ALSO
p2k(3), puffs(3), rump(3), mount_smbfs(8)
HISTORY
The rump_smbfs utility first appeared in NetBSD 6.0.
BSD
November 21, 2010 BSD