AHCISATA(4) BSD Kernel Interfaces Manual AHCISATA(4)NAME
ahcisata -- AHCI 1.0 and 1.1 compliant SATA controllers driver
SYNOPSIS
ahcisata* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The ahcisata driver supports SATA controllers compliant with the Serial ATA Advanced Host Controller Interface Revision 1.0 or 1.1 specifica-
tion, and provides the interface to the hardware for the ata(4) driver.
The ahcisata driver will only attach if the controller has been put in AHCI mode by the BIOS; if the controller is in pciide-compatible mode,
it will be handled by the appropriate driver (piixide(4) for Intel AHCI controllers).
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
Intel Corporation, Serial ATA Advanced Host Controller Interface (AHCI), Revision 1.3,
http://download.intel.com/technology/serialata/pdf/rev1_3.pdf, June 26, 2008.
BUGS
Native Command Queuing is not yet supported.
BSD March 18, 2011 BSD
Check Out this Related Man Page
JMIDE(4) BSD Kernel Interfaces Manual JMIDE(4)NAME
jmide -- JMicron Technology JMB36x PCIe to SATA II/PATA controller driver
SYNOPSIS
jmide* at pci? dev ? function ? flags 0x0000
ahcisata* at jmide?
DESCRIPTION
The jmide driver supports the JMicron Technology JMB36x IDE controllers.
These PCI-e controllers exist in different flavors (1 or 2 PATA Ultra/133 ports and/or 1 or 2 SATA-II ports), and are highly flexible. The
SATA ports can be attached to the integrated AHCI controller or attached to the PCI IDE channels in PATA emulation, in either single-drive
emulation on each PCI IDE channels, or in master/slave emulation on one of the PCI IDE channels.
When enabled, the AHCI controller can either be on the PCI function 0 or function 2. The PCI IDE controller can also be on either PCI func-
tion, and can share the PCI function with AHCI. The jmide driver supports both the AHCI controller and PCI IDE controller in various config-
urations.
SEE ALSO ahcisata(4), ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)AUTHORS
The jmide driver was written by Manuel Bouyer.
BSD July 2, 2007 BSD
CPU/Speed: PowerPC 603ev 200Mhz
Ram: 92M EDO Ram
Motherboard: Apple
Bus: 2 PCI
Cache: L1 32k and L2 256k
Controller: ATA
Disk: 2GB ATA
Load: 1 user, running httpd, Xwin, various daemons
Kernel: Linux 2.4.22-2f
Kernel ELF?: ???
pgms: gcc versión 3.2.2 20030217 (Yellow Dog Linux 3.0 3.2.2-2a);... (0 Replies)
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Hello,
I get the following in one of my error logs:
Device /dev/sda, SATA disks accessed
via libata are not currently supported by smartmontools. When libata is
given an ATA
pass-thru ioctl() then an additional '-d libata' device type will be
added to smartmontools.
---------------
I... (0 Replies)
Hello,
I get the following in one of my error logs:
Device /dev/sda, SATA disks accessed
via libata are not currently supported by smartmontools. When libata is
given an ATA
pass-thru ioctl() then an additional '-d libata' device type will be
added to smartmontools.
---------------
I... (0 Replies)
Hello,
I get the following in one of my error logs:
Device /dev/sda, SATA disks accessed
via libata are not currently supported by smartmontools. When libata is
given an ATA
pass-thru ioctl() then an additional '-d libata' device type will be
added to smartmontools.
---------------
... (1 Reply)
Discussion started by: mojoman
1 Replies
7. Post Here to Contact Site Administrators and Moderators
Where can I download the VTC - Unix Shell Scripting Advanced complete video.
I don't know in which thread I should post this question.Plz help me out, or just tell me the link in the reply to this post.
Thanks in advance. (0 Replies)
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
We have 2 controllers in storage
controller A is working, configured in Storage
Controller B is not configured in Storage, but Power supply is connected for controller B.
my query is, for some reason if power goes down for Controller A, wheather it will be redundant using Controllers... (1 Reply)
Hi All,
I have a Thinkpad - T430, which is having the wireless card as "03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205".
This one i need to configure as wifi hotspot. which i believe need to configure hostapd.conf, this kind of configuration is new to me anybody done... (1 Reply)
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Hi
I hope this is the right forum.
I am attempting to install SCO 5.0.7 on a Proliant DL380 G7 with a Smart Array P410I Controller.
I need a driver for this. Can anybody point me to a download?
Thanks in anticipation. (12 Replies)
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)