12-26-2005
HPUX Hardware commands.
HI ALL,
I am new tp HPUX and i am looking for command that will retive me the following information on HPUX:
Chassis Name & Serial Number:
Monitor
Name
BIOS
Name
EthernetPort
Name
IPEndpoint
Name
PointingDevice
Name
Keyboard
NetworkPrinter
Name
LocalPrinter
Please , please please help me with these commands....
Thanks in advance
VK
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
LEARN ABOUT NETBSD
ixpide
IXPIDE(4) BSD Kernel Interfaces Manual IXPIDE(4)
NAME
ixpide -- PCI IDE disk controllers driver
SYNOPSIS
ixpide* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The ixpide driver supports the ATI Technologies IXP IDE controller, and provides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the ixpide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
HARDWARE
The supported IDE controllers are
o ATI SB200
o ATI SB300
o ATI SB400, Parallel ATA
o ATI SB400, Serial ATA
o ATI SB700, Serial and Parallel ATA
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
CAVEATS
Some SB700 controllers can hang under load when Native IDE mode is selected in the system BIOS, but work fine in AHCI mode.
BSD
October 16, 2008 BSD