Hi folks,
I have the following configuration file,which contains list of directories:
/tmp> cat utils.conf
Backup
CPSync
Change_Listener_Port
Create_Database
Deinstall
Install_CPPlugin
Project_migrator
I have the following command in my ksh program:
mkisofs -l -L -R -V ${PACK_NAME}... (1 Reply)
Hi all,
I am new to hp-ux.I installed depot file.But i don't know how to configure that depot file.If anybody knows the configuration of depot file please help me.
It's urgent, because i have to configure that depot file.
Thanks & Regards,
Balaraju. (2 Replies)
Hi ,
a:) i have configuration file with pattren
<Range start no>,<Range end no>,<type of records to be extracted from the data file>,<name of the file to store output>
eg:
myfile.confg
9899000000,9899999999,DATA,b.dat
9899000000,9899999999,SMS,a.dat
b:) Stucture of my data file is... (3 Replies)
i am trying to use a configuration file to FTP some files.. i am not sure how to call or use a configuration file in script.
can anybody help (5 Replies)
Hi
I need a cofiguration file for my perl script...
Suppose my perl script for counting total number of user is
#!/usr/bin/perl -w
$total_users;
#To get how many users currently logged in###########
$total_users=`who | wc -l`;
print... (2 Replies)
Hi,
I have prepared a config file in which I am declaring the value for a country such as: COUNTRY=USA
Now I am trying to read the country from the config file and print a message based on the same. I have written the following code in a script and when executing the script I getting an error.
... (14 Replies)
I am new in Linux configure Apache. I got few questions to ask. I am will grateful for the help. Thanks.
1) In the Apache Configuration File, where is actually the base for the web tree?
2) I wanted to create a directory (called java) inside the base of the web tree. How am I going to do... (5 Replies)
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
LEARN ABOUT REDHAT
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO mknod(1), chown(1), mount(8), sd(4)Linux 1992-12-17 HD(4)