03-05-2008
Setting up static ip-adresses, Solaris 10
Hello,
Iam having problems getting more then one ip to work here is my setup!
Hostname: nexus
NIC: e000g1
(example ips)
My ips 80.80.80.15 to 80.80.80.20
Defaultrouter 80.80.80.1
nameservers 80.80.80.100 and 80.80.80.200
How would i do this? Any help would be mutch appriciated! Since my english isnt native so please explain as friendly as possible
Best regards emtpy
10 More Discussions You Might Find Interesting
1. Solaris
Hi All, :(:confused:
I have scoured the web and can't find this anywhere.
What I am trying to do is set up a static route through an available gateway on a server, and then test connectivity through TELNET.
I have done this on AIX (I already had this procedure).
On AIX I would use SMIT. ... (7 Replies)
Discussion started by: jeffpas
7 Replies
2. IP Networking
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Discussion started by: dlwoaud
0 Replies
3. UNIX for Dummies Questions & Answers
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies
4. Solaris
Hi,
I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ? (8 Replies)
Discussion started by: angshuman_ag
8 Replies
5. Solaris
hi,
how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies
6. IP Networking
I have been trying to setup a static ip, however everytime I do so my internet disconnects and won't connect untill I switch back to dynamic. My router is a NetGear DGN1000 and I'm using it wired. Could anyone help? (0 Replies)
Discussion started by: zomigosh
0 Replies
7. Solaris
hi guys
How to know ILOM and ALOM ip address.
how to find the ilom alerts and alom alerts can one help out pls
thanks,
deepu.
---------- Post updated at 04:39 AM ---------- Previous update was at 04:38 AM ---------- (2 Replies)
Discussion started by: pradeepaasuri
2 Replies
8. Red Hat
Hi Guys,
I want to some guidance from you in setting up the Live FTP server in Redhat Linux 6 with Static IP
120.50.150.50.
Now should I set my Static Public IP directly to my Linux machine?
If so what whould be my sunbet mask?
Is any type of natting required here? if so where would... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
9. Solaris
I have installed Solaris 11.2 in VMware Player, networked in bridged mode. When Solaris uses DHCP everything is OK, I can reach internet, as well as other systems on my LAN. When I switch to static, I have connections to my LAN, but can not get to internet, the DNS resolution is somehow not... (2 Replies)
Discussion started by: migurus
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
HT(4) Kernel Interfaces Manual HT(4)
NAME
ht - TM-03/TE-16,TU-45,TU-77 MASSBUS magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NHT ht_drives # TE16, TU45, TU77
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ht ? 172440 224 5 htintr # tu 16 massbus tape
major device number(s):
raw: 6
block: 0
minor device encoding:
bits 0003 specify HT drive
bit 0004 specifies no-rewind operation
bit 0010 specifies 1600BPI recording density instead of 800BPI
DESCRIPTION
The tm-03/transport combination provides a standard tape drive interface as described in mtio(4). All drives provide both 800 and 1600
bpi; the TE-16 runs at 45 ips, the TU-45 at 75 ips, while the TU-77 runs at 125 ips and autoloads tapes.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), tm(4), ts(4), dtab(5), autoconfig(8)
DIAGNOSTICS
tu%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
tu%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
tu%d: can't change density in mid-tape. An attempt was made to write on a tape at a different density than is already recorded on the
tape. This message is written on the terminal of the user who tried to switch the density.
tu%d: hard error bn%d er=%b ds=%b. A tape error occurred at block bn; the ht error register and drive status register are printed in
octal with the bits symbolically decoded. Any error is fatal on non-raw tape; when possible the driver will have retried the operation
which failed several times before reporting the error.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The system should remember which controlling terminal has the tape drive open and write error messages to that terminal rather than on the
console.
3rd Berkeley Distribution January 28, 1988 HT(4)