Visit Our UNIX and Linux User Community


Adding robot and drives

 
Thread Tools Search this Thread
Special Forums Windows & DOS: Issues & Discussions Adding robot and drives
# 1  
Old 04-27-2011
Adding robot and drives

Hi All

Im running veritas netbackup 6.5.5, on MWindows 2003 master server.
Ive just added a Quantum PX500 with 2 drives, the problem im facing is that now under the storage unit tab on console all the storage unit types for NDMP have the new robot listed and not the original one. The set up i need is to have the old robot TLD0 listed.
Can anyone help, the robot and drives were added via Configure storage devices Wizard.. The original robot is a ADIC 500 8 drive library.

Previous Thread | Next Thread
Test Your Knowledge in Computers #916
Difficulty: Easy
In Javascript, the console is an object which provides access to the browser debugging console.
True or False?

6 More Discussions You Might Find Interesting

1. Hardware

Arduino Robot Tank Project

Normally I'm not into kits, but I thought my wife would enjoy this one since she is a big fan of robots and droids on StarWars! We are done with the basic mechanical assembly and starting on the electronics assembly today. The robot's "brain" consists of three levels. The Arduino board, on... (5 Replies)
Discussion started by: Neo
5 Replies

2. Solaris

Adding new hard drives on Sun SPARC T5440 server with Solaris 10

I need to add two new hard drives of 300 GB capacity to a SunSPARC T5440 server. The server currently has two hard drives of 146 GB each. How do I add the new drives to the existing UFS? What are the procedures involved in setting this server with the new hard drives? I am very new to Solaris... (6 Replies)
Discussion started by: ramatnmcc
6 Replies

3. Solaris

Adding new tape drives

hi, i am using Solaris 8 on a sparc box and already have 4 tape drives in a backup libaray attached to my unix server. we have recently added 2 new tape drives to the libaray and now want to get unix to see them. have it working in windows. how do i scan for new hardware and add theses new... (5 Replies)
Discussion started by: dshakey
5 Replies

4. Solaris

Adding logical drives

Hello, I have checked in here as I dont have enough experience as Solaris Admin. My Solaris seems to boot ok on a HP Proliant DL380 G6 server The release is 5.10, the kernel ID is Generic_137138-09. It was installed after creating one logical drive type RAID1, size 300GB. Now 2 further... (2 Replies)
Discussion started by: fogarino
2 Replies

5. Filesystems, Disks and Memory

Help adding new hard drives

Folks; I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version. Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies

6. Shell Programming and Scripting

how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX

hi how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX? thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
IDA(4)							   BSD Kernel Interfaces Manual 						    IDA(4)

NAME
ida -- Compaq Intelligent Drive Array Controllers SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device ida Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): ida_load="YES" DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives into one or more high-performance logical drives. The drive array is managed by an array controller. These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface. HARDWARE
The following controllers are supported by the ida driver: o Compaq SMART Array 221 o Compaq Integrated SMART Array Controller o Compaq SMART Array 4200 o Compaq SMART Array 4250ES o Compaq SMART 3200 Controller o Compaq SMART 3100ES Controller o Compaq SMART-2/DH Controller o Compaq SMART-2/SL Controller o Compaq SMART-2/P Controller o Compaq SMART-2/E Controller o Compaq SMART Controller IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent. SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8) AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by Tom Rhodes <trhodes@FreeBSD.org>. BSD
August 8, 2004 BSD

Featured Tech Videos