10 More Discussions You Might Find Interesting
1. SCO
Sir, i have a sco 5.5 installed server and 6 clients connected through pci specialix card and printing working fine in these all terminals. 7 and 8 ports are free now, i need to setup another terminal for login on through 7 or 8 port for remote login. i connect a external modem using 25 pin male... (2 Replies)
Discussion started by: Aneesh Kumar.T
2 Replies
2. SCO
Hi,
We have a Unix 3.2v5.0.5.
I installed a printer via scoadmin, HP network printer manager with network peripheral name an ip-adress.
This is the configuration file :
root@sco1 # cat configuration
Banner: on:Always
Content types: simple
Device: /dev/null
Interface:... (4 Replies)
Discussion started by: haezeban
4 Replies
3. SCO
I have just lost all of my printers and I forget how to create a remote printer in SCO 5.07.
I do know that there is an issue with CUPS in that I have to "turn it off" (which I also forget how to do) so that this enables the "Remote Printer" setup option in Printer Administration.
I thought... (1 Reply)
Discussion started by: atpbrownie
1 Replies
4. UNIX for Advanced & Expert Users
Dear Sir
Please how can I print a job localy with my printer while a server from where I am working belong to another network?
Actulally to print a job I am oblige to :
1rst to print it inside a file
2nd coping the file to my network (rcp)
3rt sending the file to my local printer (lp... (2 Replies)
Discussion started by: sobnc
2 Replies
5. Windows & DOS: Issues & Discussions
I've been using FacetWin for some time now to connect Windows to UNIX. I have several tty's connected with a limited amount of licenses. The problem is that every time a tty gets disconnected for any reason (problems in the line, power out, etc.) I need to star killing tty's in order to free... (0 Replies)
Discussion started by: RDM00
0 Replies
6. Solaris
I am looking for a dial-up remote printing solution as under :
1. We have a Centralized location where Sun Solaris (A) is installed. From here printing command will be despatched.
2. This printing command will be routed to WAN cloud to Main Branches (B1,B2,B3)and from there, printer at... (0 Replies)
Discussion started by: jayvee
0 Replies
7. SCO
hi all,
i have recntly installed sco openserver 5.0.7. the machine is having onboard ,pci parrallel port card.while iam giving printing via onboard parallel port its printing absolutely fine.but if i give printots via pci parallel port printer prints very slowly.it stops for a few seconds... (0 Replies)
Discussion started by: arunvmk
0 Replies
8. UNIX for Advanced & Expert Users
I'm trying to print from my Solaris server to a Windows Print Server
The Print Server will then pass the print job to a PC connected via dial-up and print it locally.
EG:
Solaris
-----
| |
| |
------
/88888/
-------
\
/
... (1 Reply)
Discussion started by: warrickj
1 Replies
9. UNIX for Dummies Questions & Answers
I am using Sco Openserver 5.0.6 and I have an Okidata 16n printer on a GETNET print server.
I am able to print to the printer. However I am having display issues.
Normally when I setup a local printer I am able to tell it what model to use. Ex.(HPLaserJet).
When I setup the remote... (2 Replies)
Discussion started by: stufine
2 Replies
10. IP Networking
I am setting up a unix remote print server for approximately 500 printers. We send about 1,000 print jobs per day over the WAN. I am looking for hardware specs. I know I can overkill, but would rather get a sensible machine. Any suggestions? (2 Replies)
Discussion started by: Donna
2 Replies
enable(1) User Commands enable(1)
NAME
enable, disable - enable/disable LP printers
SYNOPSIS
/usr/bin/enable printer...
/usr/bin/disable [-c | -W] [ -r [reason]] printer...
DESCRIPTION
The enable command activates printers, enabling them to print requests submitted by the lp command. enable must be run on the printer
server.
The disable command deactivates printers, disabling them from printing requests submitted by the lp command. By default, any requests that
are currently printing on printer will be reprinted in their entirety either on printer or another member of the same class of printers.
The disable command must be run on the print server.
Use lpstat -p to check the status of printers.
enable and disable only effect queueing on the print server's spooling system. Executing these commands from a client system will have no
effect on the server.
OPTIONS
The following options are supported for use with disable:
-c Cancels any requests that are currently printing on printer. This option cannot be used with the -W option. If the printer
is remote, the -c option will be silently ignored.
-W Waits until the request currently being printed is finished before disabling printer. This option cannot be used with the
-c option. If the printer is remote, the -W option will be silently ignored.
-r [reason] Assigns a reason for the disabling of the printer(s). This reason applies to all printers specified. This reason is
reported by lpstat -p. Enclose reason in quotes if it contains blanks. The default reason is "unknown reason" for the
existing printer, and "new printer" for a printer added to the system but not yet enabled.
OPERANDS
The following operand is supported for both enable and disable:
printer The name of the printer to be enabled or disabled. Specify printer using atomic name. See printers.conf(4) for information
regarding the naming conventions for atomic names.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
FILES
/var/spool/lp/* LP print queue.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWpcu |
+-----------------------------+-----------------------------+
|CSI |enabled |
+-----------------------------+-----------------------------+
SEE ALSO
lp(1), lpstat(1), printers.conf(4), attributes(5)
SunOS 5.10 9 Sep 1996 enable(1)