Serial port redirector

10 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. Programming

Read from serial port

Hi I try to communicate with a GSM modem, from C, for sending SMS. I use standart AT-commands. Working well with terminal. There is no problem writing ti the port. But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35...

3. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

4. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

5. Windows & DOS: Issues & Discussions

Telnet to a serial port

Hello all. I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions: How can i configure the serial port on dos? How can i telnet form dos to the serial port? How can i set up a telnet server on the...

6. AIX

Serial port in AIX

Hi, How can i configure my modem in AIX thru serial port (sa0-->tty0) I have two port serial card configured as sa0 I created tty1 which port is tty0 and which port is tty1 how can i know??

7. Programming

Programming serial port

Hello! Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements: 1. Serial port is opened in non-canonical mode. 2. All the time I need to check is there something to read. 3. If I have to write something I need to write it...

8. Programming

Serial port programming

I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than...

9. UNIX for Advanced & Expert Users

Communicating with Serial Port

I am using system running on red hat linux 4. I had connected health measuring machine to the serial port and configured it stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the...

10. UNIX for Advanced & Expert Users

UNIX Serial Port Redirector

Hi , I need to have an application where in I am able to create a virtual Serial port on a UNIX machine for a remote device which is accessible by a IP address and a port number (by terminal server). Both the machine and the remote device are on the same network. So after this application is...

LEARN ABOUT NETBSD

scc

SCC(4)							   BSD Kernel Interfaces Manual 						    SCC(4)

NAME

     scc -- Zilog 8530 Serial Communications Controller interface

SYNOPSIS

     scc* at ioasic? offset ?

DESCRIPTION

     The scc driver provides support for the Zilog 8530 Serial Communications Controller (SCC) via the IOASIC found on DECstation 5000 models in
     the /100, /20, and /240 series (supported by NetBSD/pmax).

     Each SCC device has two serial ports.  The DECstation 5000 model 20 provides one SCC device.  Other models provide two, but one port of each
     device is dedicated to mouse and keyboard input, respectively.

     Input and output for each line may set to one of following baud rates: 50, 75, 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 4800, 9600,
     19200, 38400, or 57600.

     Speeds up to 230400 are supported by the chip and the motherboard, but speeds higher than 57600 do not work reliably without an external
     clock signal.

FILES

     /dev/ttya
     /dev/ttyb
     /dev/ttyc
     /dev/ttyd

     The mapping from units to serial-hardware outlets is idiosyncratic.  The even ports are wired serial connectors and the odd-numbered ports
     are reserved for mouse and keyboard.

     On machines with one port like Personal DECstations, the single device is ttya.

     On the 5000/1xx and 5000/2xx, the first serial port (default serial console) is ttyc and the second port is ttya.

SEE ALSO

     intro(4), ioasic(4), ttys(5), MAKEDEV(8)

HISTORY

     The scc driver first appeared in 4.4BSD.

     The scc driver was also used for the IOASIC SCC found in DEC Alpha model 3000 TurboCHANNEL based systems; NetBSD/alpha has since been con-
     verted to use the machine-independent zstty(4).

BUGS

     The IOASIC provides internal DMA channels that can be programmed to transfer up to 4096 bytes of data into, or out, of an SCC without further
     software intervention.  This feature of the IOASIC is not yet supported.

     The mapping from device-special files (major and minor number) to chip and port is arguably backwards.  ULTRIX tries to hide the hardware
     mapping, but NetBSD does not.  Users wanting to use ULTRIX compatible tty names /dev/tty0 and /dev/tty1 for the scc comm-port lines should
     make links or device-special files which match their hardware setup.

BSD
								  April 24, 2003							       BSD

UNIX for Dummies Questions & Answers