10 More Discussions You Might Find Interesting
1. AIX
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
2. AIX
Hi
In my vio server I have the below output
$ lsvopt | grep -i SAPSITGS
sapsitgs_cdrom TL12UP.iso 3182
In my vio client lpar I have the below output
root@sapsitgs:/ # lsdev -Cc cdromcd0 Available Virtual SCSI Optical Served by VIO Server
cd1... (1 Reply)
Discussion started by: newtoaixos
1 Replies
3. AIX
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
Discussion started by: petervg
6 Replies
4. AIX
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Discussion started by: Johnny1314
2 Replies
5. AIX
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Discussion started by: ms1232
1 Replies
6. AIX
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
Discussion started by: filosophizer
5 Replies
7. AIX
hello Folks,
my vio:
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- -------------------------------------------- ------------------
vhost0 U9117.MMA.6534BE4-V2-C11 0x00000003
VTD ... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. AIX
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Discussion started by: daveisme
4 Replies
9. AIX
Hi, I've lost the root password in a virtual partition created in a IBM Vio Server. May I recover that somehow?
Thanks (2 Replies)
Discussion started by: r4mp4g3
2 Replies
10. AIX
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Discussion started by: scottsl
1 Replies
roar_vs_file(3) RoarAudio Programmer's Manual roar_vs_file(3)
NAME
roar_vs_file, roar_vs_file_simple, roar_vs_new_from_file - File mode for VS API
SYNOPSIS
#include <roaraudio.h>
int roar_vs_file(roar_vs_t * vss, struct roar_vio_calls * vio, int closefile, int * error);
int roar_vs_file_simple(roar_vs_t * vss, char * filename, int * error);
roar_vs_t * roar_vs_new_from_file(const char * server, const char * name, char * filename, int * error);
DESCRIPTION
These functions are used to open the VS object in file mode. In the file mode the VS API reads or writes the data from or to the file
itself. The file mode uses normal VIO/DSTR so it supports streams as well. Just pass the stream URL as filename.
roar_vs_file() sets up the file mode for a already opened object using the open VIO handle vio. This function requires the use of
roar_vs_stream(3).
roar_vs_file_simple() sets up the file mode using a given filename (or URL). It opens the file using DSTR API. By default the function
assumes playback mode and tries to auto detect the audio parameters. To override the auto detection or use a diffrent stream direction use
roar_vs_stream(3).
roar_vs_new_from_file() creates a new VS object and enters file mode using the file (or URL) given as filename.
To send data to or read data from use roar_vs_iterate(3) or roar_vs_run(3).
PARAMETERS
server The server to connect to. NULL for defaults.
name The application name. This should be something the user can use to identify the application. It MUST NOT be the application's
binary name or the value of argv[0].
vio The VIO handle to be used by the file mode.
closefile
This parameter tells the file mode if the file should be closed on roar_vio_close(3). Must be ROAR_VS_TRUE (common) or
ROAR_VS_FALSE.
filename
The filename used to open the file for file mode. The file is opend using DSTR API. All kinds of files supported by DSTR are sup-
ported. This includes HTTP streams.
error This is a pointer to a integer used to store the error value in case of error. This can be NULL if not used but it is very recom-
mended to use this error value to report good error messages to the user.
RETURN VALUE
On success roar_vs_new_from_file() return a new VS object. On error, NULL is returned. roar_vs_file() and roar_vs_file_simple() returns 0
on success and -1 on error.
EXAMPLES
roar_vs_t * vss;
int err;
vss = roar_vs_new_from_file(NULL, "MyApp", "http://...", &err);
if ( vss == NULL ) {
//handle error.
}
if ( roar_vs_run(vss, &err) == -1 ) {
//handle error.
}
if ( roar_vs_close(vss, ROAR_VS_FALSE, &err) == -1 ) {
//handle error.
}
SEE ALSO
roar_vs_new_simple(3), roar_vs_iterate(3), roar_vs_run(3), roar_vs_close(3), roarvs(7), libroar(7), RoarAudio(7).
RoarAudio June 2011 roar_vs_file(3)