10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI.
I can get as far as plugging it in on my own.
Please help
Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
2. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
3. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
6. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
7. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
8. UNIX for Advanced & Expert Users
Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say:
pcipsy0: This is block
Can someone please help me. I trying to hook... (2 Replies)
Discussion started by: aojmoj
2 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks (2 Replies)
Discussion started by: nattie_h
2 Replies
10. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
TAPSET::SCSI(3stap) TAPSET::SCSI(3stap)
NAME
tapset::scsi - systemtap scsi probe points
DESCRIPTION
This family of probe points is used to probe the SCSI activities. It contains the following probe points:
scsi.ioentry
Fires when SCSI mid layer prepares a SCSI request
Arguments:
disk_major
The major number of the disk
disk_minor
The minor number of the disk
device_state
The current state of the device. The possible values could be:
SDEV_CREATED = 1, /* device created but not added to sysfs
* Only internal commands allowed (for inq) */
SDEV_RUNNING = 2, /* device properly configured
* All commands allowed */
SDEV_CANCEL = 3, /* beginning to delete device
* Only error handler commands allowed */
SDEV_DEL = 4, /* device deleted
* no commands allowed */
SDEV_QUIESCE = 5, /* Device quiescent. No block commands
* will be accepted, only specials (which
* originate in the mid-layer) */
SDEV_OFFLINE = 6, /* Device offlined (by error handling or
* user request */
SDEV_BLOCK = 7, /* Device blocked by scsi lld. No scsi
* commands from user or midlayer should be issued
* to the scsi lld. */
scsi.iodispatching
Fires when the SCSI mid layer dispatches a SCSI command to the low level driver
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device.
data_direction
The data_direction specifies whether this command is from/to the device.
The possible values could be:
DMA_BIDIRECTIONAL = 0,
DMA_TO_DEVICE = 1,
DMA_FROM_DEVICE = 2,
DMA_NONE = 3,
request_buffer
The request buffer address
req_bufflen
The request buffer length
scsi.iodone
Fires when a SCSI command is done by low level driver and enqueued into the done queue.
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
scsi.iocompleted
Fires when SCSI mid layer runs the completion processing for block device I/O requests
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
goodbytes
The bytes completed.
SEE ALSO
stap(1), stapprobes(3stap)
IBM
TAPSET::SCSI(3stap)