usb hdd detection problem

9 More Discussions You Might Find Interesting

1. Red Hat

USB HDD not showing valid partition on one Solaris machine

Hi All, We have got a USB HDD with important data in it. The data has been copied to the disk(formatted ext3) via a LINUX system. The data was supposed to be copied to a second LINUX machine. Surprisingly, it doesn't show up any valid partitions in the new box. dmesg: usb1-3:...

2. Programming

Parallel Processing Detection and Program Return Value Detection

Hey, for the purpose of a research project I need to know if a specific type of parallel processing is being utilized by any user-run programs. Is there a way to detect whether a program either returns a value to another program at the end of execution, or just utilizes any form of parallel...

3. Solaris

NIC detection problem in solaris

Hi, Hardware: Mother board: Asus P5G4IC-M LX On board NIC: PCIe Gigabite LAN Kernel Ver.: SunOS 5.10 Generic_141445-09 I've NIC detection problem in Solaris 10. When I was trying to install in x86 machine, it was not asking for any Network settings which means it couldn't find NIC. But...

4. Filesystems, Disks and Memory

How to stop USB-HDD?

Hi, There is the following minor issue with USB-harddrive: On windows: when i perform "safely remove" disk is stopped (hdd head is parking) & it is not spinning (but it is still connected to USB) On Linux (Fedora 14, OpenSUSE): when i perform "umount", HDD is still spinning. Could you...

5. Ubuntu

Lucid AMD 64 install on USB HDD reboots frequently

Hi all, I am using Ubuntu lucid. It is installed on external USB HDD and I boot into it. Besides other issues, the most significant one is as follows.. I boot in and start working. Everything goes on fine. As soon as I move the HDD, change its position, etc, all icons tuns into a red...

6. UNIX for Dummies Questions & Answers

How to copy my system hdd usb stick from 4GB to 8GB ?

Hi, my router is my Linux embedded device. I have system installed on HDD 4GB usb stick, part1 swap, part2 /opt , part3 data. I need to copy my system to new HDD 8GB usb stick. What is a way for 4GB > 4GB HDD and what for 4GB > 8GB As I remeber, I can copy image of my 4GB HDD usb stick...

7. Filesystems, Disks and Memory

external USB detection problems

I have seagate USB 2.0 HDD which was working good on my windows system Recently I have started using red hat Linux 2.6.9-55.0.12.EL (i686 i686 i386 GNU/Linux) The USB is not at all detected in Linux even if I reboot with it attached to the PC. The same can be detected on any Windows system....

8. Solaris

Another Urgent HDD problem

I have another Hdd problem with Ultra 1 machine the hdd is segate (+-)17560 MB and when I start installtion of sun solaries 2.6 the system sees the hdd correctly, and the installtion goes fine with partioning the disk as follows / 150 MB swap 500 MB /user 1000 MB /user1 100MB /usr3 5500 MB...

9. HP-UX

Hdd problem, help!!!

Hi, My HP-UX has some errors to wake up and one of them are: /dev/vg00/rlvol4 BAD CYLINDER GROUPS I have thought that my hdd has physical problems, my question is: Exists a program to check the hdd physically and to repair it... Thanks....

LEARN ABOUT FREEBSD

usb_template

USB_TEMPLATE(4) 					   BSD Kernel Interfaces Manual 					   USB_TEMPLATE(4)

NAME

     usb_template -- USB templates

SYNOPSIS

     To compile this module into the kernel, place the following line in your kernel configuration file:

	   device usb_template

     To load the module at boot time, place the following line in loader.conf(5):

	   usb_template_load="YES"

DESCRIPTION

     The usb_template module implements various USB templates that are needed when programming an USB device side driver.  A USB template consists
     of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
     descriptors, USB strings and additional USB descriptors.  The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
     ernet and Message Transfer Protocol.  USB templates are currently selected using the "hw.usb.template" sysctl.  The "hw.usb.template" value
     can be changed at any time, but will not have any effect until the USB device has been re-enumerated.

SEE ALSO

     usb(4)

STANDARDS

     The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.

HISTORY

     The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.

BSD
								  March 18, 2014							       BSD

UNIX for Dummies Questions & Answers