Defining a fiber attached tape drive NEED HELP PLZ!

8 More Discussions You Might Find Interesting

1. AIX

Has anyone created JFS2 file system on a USB drive attached to AIX server?

We have an IBM Power 710. It has a USB port on the front. I have done some searching and see that there is information out there on how to create a JFS2 file system on USB drives. A few have commented that they would not recommend it, if the server is important, may crash the server... Just...

2. HP-UX

TAPE drive

I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help? Thanks in advance

3. Solaris

Help with tape drive

Hey folks, Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes. I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V. As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly. ...

4. Solaris

SAN connection - configuring fibre attached hard drive

Hi All, I recently got a connection to the SAN through a fibre channel on my solaris box: #luxadm -e port /devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:devctl CONNECTED #ls -l /dev/cfg lrwxrwxrwx 1 root root 48 Feb 23 12:31 c4 -> ../../devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:fc I then...

5. Solaris

Solaris 10 new fiber connected tape

Hello all, how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks Best Regards

6. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

7. Solaris

Cloning the root drive - Help Plz

I use Sunfire V480R , and i am seeing lot of scsi transport errors for the root drive & i think it is going to die . the system is having 2 drives & the second drive is kept unused . can someone guide me how do i clone the root drive to the seconddrive and make that bootable .

8. UNIX for Dummies Questions & Answers

tape drive

Hi, I need to restore my tape backup, when I type "tape status" it gives; status : ready beginning-of-tape write-protected soft errors : 0 hard errors : 0 underruns : 3 but...

LEARN ABOUT NETBSD

mlxctl

MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME

     mlxctl -- Mylex DAC960 family management utility

SYNOPSIS

     mlxctl [-f dev] [-v] [-a] status [drive] [...]
     mlxctl [-f dev] [-a] detach [drive] [...]
     mlxctl [-f dev] [-a] check [drive] [...]
     mlxctl [-f dev] rebuild channel:target
     mlxctl [-f dev] cstatus
     mlxctl [-f dev] rescan
     mlxctl [-f dev] config

DESCRIPTION

     The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.

     The following options are available:

     -a       Apply the action to all drives attached to the controller.

     -f dev   Specify the control device to use.  The default is /dev/mlx0.

     -v       Increased verbosity.

     The following commands are available:

     cstatus  Display the controller's current status.

     status   Display the status of the specified drives.  This command returns 0 if all drives tested are online, 1 if one or more drives are
	      critical and 2 if one or more are offline.

     rescan   Re-scan the logical drive table, and attach or detach devices from the system as necessary.

     detach   Detach the specified drives.  Drives must be unmounted and unopened for this command to succeed.

     check    Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5).	This command returns imme-
	      diately.	The status command can be used to monitor the progress of the check.

     rebuild  Rebuild onto the specified physical drive.  Note that there can be only one running rebuild operation per controller at any given
	      time.  This command returns immediately.	The cstatus command can be used to monitor the progress of the rebuild.

     config   Write the current system drive configuration to stdout.

EXAMPLES

     Display the status of drive ld3 attached to the controller mlx1:

	   mlxctl -f /dev/mlx1 -v status ld3

SEE ALSO

     ld(4), mlx(4)

HISTORY

     The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.

BUGS

     Modifying drive configuration is not yet supported.

     Some commands do not work with older firmware revisions.

     Error log extraction is not yet supported.

BSD
								  April 10, 2000							       BSD

UNIX for Dummies Questions & Answers