SCO OS5 Boot up stops

10 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

IBM eServer X 335 stops boot process at Server splash screen

Hi there. I used to use linux a lot a number of years ago but it has been quite a while so ?I really consider myself a beginner again. I have an old IBM eServer X Series 335 machine and I want to get it back up and running for a number of reasons. I knew that one of the SCSI drives was bad and...

2. UNIX for Beginners Questions & Answers

SCO OpenServer 5 Will Not Boot

We have a legacy system that runs on SCO OpenServer 5.0.6, and I've rebuilt the server a couple of times so we can have access to old historical data. That system suddenly went offline for no known reason, and I know that the configuration has not been altered, there is nobody with access to the...

3. SCO

Sco UNIX 5.0.6 not boot

hi i have image SCo Unix 5.0.6 and I want transfer on my HP ML350 G5 after Transfer show this message : boot not found cannot open stage 1 boot failure: error loading hd (40)/boot this hp server used smart array E200i and P400 and sco not recognized HDD tanks

4. SCO

SCO Will Not Boot

Hello to all , I am new to this forum and also i have very less knowledge about sco unix, but I have good knowlage about Dos-Windows file systems since 1990 year :) and i am a professional IT person about Networking and computer hardware but as i said not know much about Unix based systems :( ,...

5. HP-UX

HP-UX stops on boot; DIAGNOSTIC SYSTEM WARNING

Hi all, I have an HP-UX server that halts during boot. Below is CO output. Any ideas how to solve this? Any help would be appreciated. Thank you. HP-UX Boot Loader for IPF -- Revision 2.027 Press Any Key to interrupt Autoboot \EFI\HPUX\AUTO ==> boot vmunix -lq Seconds left till...

6. SCO

Want to set up SNMP with MIB on SCO OS5

Want to setup snmp with mib to track system issues on SCO OS5.0.5. Is there somewhere I can look that will give me insight in how to answer some of the questions the mkdev snmp asks?

7. UNIX for Advanced & Expert Users

Error during Sco Unix boot

Hi friends, i am getting the following error while booting my system which has SCo UNIX . ========================= H iinit PANIC: srmountfun-Error 22 mounting of rootdev hd(1/42) cannot dump 40863 pages to dempdev hd(1/41) : Space for only 0 pages. Dump not completed. safe to power off...

8. UNIX for Dummies Questions & Answers

boot failure SCO 5.0.6 OpenServer

hello guys. I just installed SCO 5.0.6 OpenServer it went all the way to the end of the installation and the first boot try it gave me this message. not a directory boot not found cannot open stage 1 boot failure: error loading hd (40)/boot

9. UNIX for Dummies Questions & Answers

SCO os5 xwindow

I acciedentaly terminated the x window session on my sco os5 machine. Can somone help me get it going again with out rebooting? Another ? Does anyone know where I can get the VNC version for SCO or can some one help me make changes to the RH version to work for SCO OS5. Thanks.

10. UNIX for Dummies Questions & Answers

Making boot disks in SCO

This last monday the inittab file became corrupted and the server refused to start... A set of boot / root disks made from another SCO server saved the day.. Anyway, I would like to make a set from the production server just so I have a set created from that machine. The command I would be using is...

LEARN ABOUT NETBSD

ubt

UBT(4)							   BSD Kernel Interfaces Manual 						    UBT(4)

NAME

     ubt -- USB Bluetooth driver

SYNOPSIS

     ubt* at uhub? port ? configuration ? interface ?

DESCRIPTION

     The ubt driver provides support for USB Bluetooth dongles to the Bluetooth protocol stack.

     USB Bluetooth dongles provide two interfaces, both of which the ubt driver claims.  The second interface is used for Isochronous data and
     will have several alternate configurations regarding bandwidth consumption, which can be set using the hw.ubtN.config sysctl(8) variable.
     The number of alternate configurations is indicated by the value in the hw.ubtN.alt_config variable, and the isoc frame size for the current
     configuration is shown in the hw.ubtN.sco_rxsize and hw.ubtN.sco_txsize variables.

     By default, configuration 0 is selected, which means that no bandwidth is used on the Isochronous interface and no SCO data can be sent.
     Consult the Bluetooth USB specification at https://www.bluetooth.org/ for complete instructions on setting bandwidth consumption.	The fol-
     lowing extract may be useful as a general guidance though details may differ between manufacturers.

     0	  No active voice channels
     1	  One voice channel with 8-bit encoding
     2	  Two voice channels with 8-bit encoding, or one voice channel with 16-bit encoding.
     3	  Three voice channels with 8-bit encoding
     4	  Two voice channels with 16-bit encoding
     5	  Three voice channels with 16-bit encoding

SEE ALSO

     bluetooth(4), uhub(4), sysctl(8)

HISTORY

     This ubt device driver was originally a character device written by David Sainty and Lennart Augustsson.  It was rewritten to support socket
     based Bluetooth access for NetBSD 4.0 by Iain Hibbert.

CAVEATS

     Isochronous data is seemingly not well supported over USB in the current system and to get SCO working, you may have to calculate the SCO
     packet size that the stack will use.  This is the sco_mtu value reported by the btconfig(8) command, and when combined with the SCO header (3
     bytes) should fit exactly into an integer number of Isochronous data frames where the frame size is indicated by the 'hw.ubtN.sco_txsize'
     sysctl variable.

     For example: I want one voice channel (which is all that is supported, for now) so am using configuration #2, with a frame length of 17
     bytes.  This gives possible values of:

	   (17 * 1) - 3 = 14
	   (17 * 2) - 3 = 31
	   (17 * 3) - 3 = 48
	   (17 * 4) - 3 = 65
	   (17 * 5) - 3 = 82
	   etc.

     btconfig(8) shows the maximum SCO payload as 64 bytes, so I am using the next smaller size of 48, to minimize the overhead of the 3 header
     bytes.

     The SCO packet size can be changed using the 'scomtu' option to btconfig(8).

     The failure mode is that the USB Bluetooth dongle locks up though generally removal/reinsertion will clear the problem.

BUGS

     The Isochronous configuration can only be changed when the device is not marked up.

BSD
								  August 27, 2006							       BSD

UNIX for Dummies Questions & Answers