10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Hi there.
I used to use linux a lot a number of years ago but it has been quite a while so ?I really consider myself a beginner again.
I have an old IBM eServer X Series 335 machine and I want to get it back up and running for a number of reasons. I knew that one of the SCSI drives was bad and... (2 Replies)
Discussion started by: filch2
2 Replies
2. UNIX for Beginners Questions & Answers
We have a legacy system that runs on SCO OpenServer 5.0.6, and I've rebuilt the server a couple of times so we can have access to old historical data. That system suddenly went offline for no known reason, and I know that the configuration has not been altered, there is nobody with access to the... (63 Replies)
Discussion started by: spock9458
63 Replies
3. SCO
hi
i have image SCo Unix 5.0.6 and I want transfer on my HP ML350 G5
after Transfer show this message :
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
this hp server used smart array E200i and P400 and sco not recognized HDD
tanks (7 Replies)
Discussion started by: moein.mojtaba
7 Replies
4. SCO
Hello to all , I am new to this forum and also i have very less knowledge about sco unix, but I have good knowlage about Dos-Windows file systems since 1990 year :) and i am a professional IT person about Networking and computer hardware but as i said not know much about Unix based systems :( ,... (7 Replies)
Discussion started by: meraklinext
7 Replies
5. HP-UX
Hi all,
I have an HP-UX server that halts during boot. Below is CO output.
Any ideas how to solve this? Any help would be appreciated. Thank you.
HP-UX Boot Loader for IPF -- Revision 2.027
Press Any Key to interrupt Autoboot
\EFI\HPUX\AUTO ==> boot vmunix -lq
Seconds left till... (0 Replies)
Discussion started by: MazenH
0 Replies
6. SCO
Want to setup snmp with mib to track system issues on SCO OS5.0.5. Is there somewhere I can look that will give me insight in how to answer some of the questions the mkdev snmp asks? (0 Replies)
Discussion started by: herd5cusa
0 Replies
7. UNIX for Advanced & Expert Users
Hi friends,
i am getting the following error while booting my system which has SCo UNIX .
=========================
H iinit
PANIC: srmountfun-Error 22
mounting of rootdev hd(1/42)
cannot dump 40863 pages to dempdev hd(1/41) : Space for only 0 pages.
Dump not completed.
safe to power off... (3 Replies)
Discussion started by: sveera
3 Replies
8. UNIX for Dummies Questions & Answers
hello guys.
I just installed SCO 5.0.6 OpenServer it went all the way to the end of the installation and the first boot try it gave me this message.
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot (2 Replies)
Discussion started by: josramon
2 Replies
9. UNIX for Dummies Questions & Answers
I acciedentaly terminated the x window session on my sco os5 machine. Can somone help me get it going again with out rebooting? Another ? Does anyone know where I can get the VNC version for SCO or can some one help me make changes to the RH version to work for SCO OS5.
Thanks. (2 Replies)
Discussion started by: ruizf
2 Replies
10. UNIX for Dummies Questions & Answers
This last monday the inittab file became corrupted and the server refused to start... A set of boot / root disks made from another SCO server saved the day.. Anyway, I would like to make a set from the production server just so I have a set created from that machine. The command I would be using is... (1 Reply)
Discussion started by: LowOrderBit
1 Replies
MKFS.BFS(8) Linux System Administrator's Manual MKFS.BFS(8)
NAME
mkfs.bfs - make an SCO bfs filesystem
SYNOPSIS
mkfs.bfs [-N nr-of-inodes] [-V volume-name] [-F fsname] device [size-in-blocks]
DESCRIPTION
mkfs.bfs creates an SCO bfs file-system on a block device (usually a disk partition or a file accessed via the loop device).
The size-in-blocks parameter is the desired size of the file system, in blocks. If nothing is specified, the entire partition will be
used.
OPTIONS
-N Specify the desired number of inodes (at most 512). If nothing is specified some default number in the range 48-512 is picked
depending on the size of the partition.
-V volume-label
Specify the volume label. I have no idea if/where this is used.
-F fsname
Specify the fsname. I have no idea if/where this is used.
-v Be verbose.
EXIT CODES
The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.
SEE ALSO
mkfs(8).
AVAILABILITY
The mkfs.bfs command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
Util-linux 2.9x 12 Sept 1999 MKFS.BFS(8)