10 More Discussions You Might Find Interesting
1. SCO
I am very new to SCO Unix so I apologize if this is a easy or dumb question.
I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as... (10 Replies)
Discussion started by: NPIGuy
10 Replies
2. SCO
Hi all
Can anybody offer any help with installing Openserver 6 on a Supermicro server?
I am familiar with installing OS5, but this is my first time with v6.
The PC is fitted with Supermicro X8DTL-I Dual Xeon motherboard and 2 Xeon E5620 processors, and 16Gb Ram, LSI MegaRaid SAS8708 8 port... (11 Replies)
Discussion started by: millosman
11 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. SCO
Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies
5. SCO
Dear all,
I'm newbie in SCO. I already purchase SCO 5.0.7 and SATA Tape Drive (not SCSI) for IBM server. not a cheap investment :(
my problem is:
I can't use my sata tape on sco 5.0.7 for backup my data because sco can't detect any sata tape has been plug into o/s. i already running "mkdev... (7 Replies)
Discussion started by: asumatezuka
7 Replies
6. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
7. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
8. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
9. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
10. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
diskd(1) General Commands Manual diskd(1)
Name
diskd - disk daemon; wait for disk to be inserted
Note
This manpage has been automatically generated from fdutils's texinfo documentation. However, this process is only approximative, and some
items, such as cross-references, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate rep-
resentation in the manpage format. Moreover, only the items specific to each command have been translated, and the general information
about fdutils has been dropped in the manpage version. Thus I strongly advise you to use the original texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips fdutils.dvi
* To generate a HTML copy, run:
./configure; make html
A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as HTML. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
Description
The diskd command has the following syntax:
diskd [-d drive] [-i interval] [-e command]
Diskd waits for a disk to be inserted into a given drive, and then either executes the command or exits. This program can be used to auto-
matically mount a disk as soon as it is inserted.
Warning
This program works by switching the motor on for a very short interval, and then seeking to track -1. This might damage hardware in the
long run. Amigas, which also use these techniques, are known for having problems with their disk drives no longer spinning up properly
after a few month of usage.
Options
-d drive
Selects the drive to observe for disk insertion. By default, drive 0 (/dev/fd0) is observed.
-i interval
Selects the polling interval. The interval is given in tenths of seconds. Default is 10 (one second).
-e command
Gives the command to be executed when a disk is inserted. If no command is given the program simply exits. Typically, the command
mounts the disk. It can be a shell scripts which probes for several filesystems and disk geometries until it succeeds.
Bugs
* Automatic unmounting cannot yet be handled. It is indeed not enough to scan for disk removal, because when the disk is removed, it
is already too late: There might be some buffers needing flushing. However, the fdmountd program allows automatic unmounting by
using the SYNC mount options, which switches off write buffering (see section fdmount).
* The drive motor is running all the time, and on some computers, the drive led flickers at each time the drive is polled.
See Also
Fdutils' texinfo doc
fdutils-5.5 03Mar05 diskd(1)