I'm running a Linux OS that uses Debian as it's base. A commercial vpn is installed that uses OpenVPN. For some reason, I can't get ipv6 to tunnel properly .... and Ipleak.net shows that my location is being unmasked by ipv6.
I've tried kernel commands at boot, I've tried sysctl.conf commands. Just can't get ipv6 to go away and stay away during boot. So far have several hours of search time in it.
Can you show us the output from:-
If there is nothing in those that is setting it, then it may be getting forced by the VPN software, which you don't tell us much about.
Would you not need an IPv6 definition to be able to use IPv6 tunnelling? Are you trying to prevent IPv6 access entirely or just heavily restrict it? I'm confused in your requirement.
Can you show us the output from:-
If there is nothing in those that is setting it, then it may be getting forced by the VPN software, which you don't tell us much about.
Would you not need an IPv6 definition to be able to use IPv6 tunnelling? Are you trying to prevent IPv6 access entirely or just heavily restrict it? I'm confused in your requirement.
Thanks, in advance,
Robin
Thanks for the response. The OS became so unstable that it would not boot. Finally, I ended up reloading the OS today. I'm on a different distro now.
When I installed the VPN, I had disabled ipv6 and verified by ipleak.net that the system was stealth. Days later, ipv6 made it off the machine. I caught it when a routine check of ipleak.net reported that I was being unmaked by ipv6. As my VPN was not tunneling ipv6, I was just attempting to turn it off.
I still very much a newbie and making lots of mistakes. I'll finish the config of this machine tomorrow or the next day and see if the problem returns.
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
I am trying to setup an IPv6 network.
I modified the interfaces file:
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
iface etho0 inet static
address 2620:7:a000::1
netmask 64
gateway ::ffff:c0a8:101
... (0 Replies)
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
my problem: i want to change from ipv4 to ipv6 on my home network.
On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0
Editing netconf-ipv6 i can assing a routable ipv6 address like
fd55:282f:3b98::/48
or
2001:470:26:307:89a0:aba1:f98b:eb3e
but only to alias... (0 Replies)
Hi! I have to configure ipv6 network between two computers with Solaris 10 but I not an expert in using any unix system and I do it becouse I need it to my study. Is someone here who could help me and describe step-by-step how to do it? please!!!
PS. I need to configure network to do secure... (1 Reply)
Hello guyz..
did some of u have implement or making a testbed for IPv6?
if yes, can u attached the procedures and standard guidelines because i really need for my proposal..
thanx.. (2 Replies)
I am using digital Unix and lpd. I have HP 4200n LaserJet TCP printer, but when I use lpr command, it always print duplex.
I can turn off duplex feature at the panel of the printer, but then other Windows computer cannot print duplex. How can I set up /etc/printcap file so that it will be... (2 Replies)