Ipv6 on hpux

8 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in...

2. IP Networking

IPv6 Problems

I am trying to setup an IPv6 network. I modified the interfaces file: /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback iface etho0 inet static address 2620:7:a000::1 netmask 64 gateway ::ffff:c0a8:101 ...

3. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your...

4. HP-UX

pwage-hpux-T for Trusted HPUX servers

I'm sharing this in case anybody needs it. Modified from the original solaris pwage script. This modified hpux script will check /etc/password file on hpux trusted systems search /tcb and grep the required u_succhg field. Calculate days to expiry and notify users via email. original solaris...

5. SuSE

Linux and IPv6

Hi gurus, In a few month, we must enable IPv6 on our Linux Server! Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files? Could Linux run simultaneous IPv4 and IPv6? Thanks in advance for our help our ideas? Best regards, nm

6. Shell Programming and Scripting

Need Script to Use CPUs on a HPUX server to simulate Workload Manager on HPUX.

I am running HPUX and using WLM (workload manager). I want to write a script to fork CPUs to basically take CPUs from other servers to show that the communication is working and CPU licensing is working. Basically, I want to build a script that will use up CPU on a server. Any ideas?

7. AIX

IPv6 on AIX

Hi Every1, I want to configure IPv6 on AIX and want to communicate between IPv4 machine IP and IPv6 machine. Is it possible?

8. IP Networking

IPv6 testbed

Hello guyz.. did some of u have implement or making a testbed for IPv6? if yes, can u attached the procedures and standard guidelines because i really need for my proposal.. thanx..

LEARN ABOUT FREEBSD

flowctl

FLOWCTL(8)						    BSD System Manager's Manual 						FLOWCTL(8)

NAME

     flowctl -- ng_netflow(4) control utility

SYNOPSIS

     flowctl [-d level] path command

DESCRIPTION

     The flowctl utility is intended to control the ng_netflow(4) nodes.  It has a single option:

     -d level  Set the netgraph(3) debugging level to level.

COMMANDS

     Currently, flowctl supports only one command.

     show [ipv4|ipv6] [human|verbose]
	   This command is the analog of the ``show ip cache flow'' command of a Cisco router.	It dumps the contents of the flow cache in Cisco-
	   like format.  Specifying either ipv4 or ipv6 would extract only IPv4 or IPv6 flows respectively.  It has optional parameter verbose,
	   which is analog of the ``show ip cache verbose flow'' command. Additionally, human parameter can be specify to show selected flows in
	   human-readable format.

EXIT STATUS

     The flowctl utility exits 0 on success, and >0 if an error occurs.

SEE ALSO

     netgraph(3), ng_netflow(4)

AUTHORS

     The flowctl utility was written by Gleb Smirnoff <glebius@FreeBSD.org>, based on ipacctctl written by Roman V. Palagin <romanp@unshadow.net>.

BSD
								   June 8, 2012 							       BSD

HP-UX