10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
2. Solaris
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk... (0 Replies)
Discussion started by: gjackson123
0 Replies
3. Solaris
I have a v480 with a mirrored boot disk c1t0 and c1t1. The drives themselves don't show a failure but the mirror's need maintenance.
This is my plan for replacing the drive. I would love feedback to point out what I"m missing or where my steps are incorrect.
Two things I believe I'm... (3 Replies)
Discussion started by: pcoffey
3 Replies
4. Solaris
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
Discussion started by: TKD
6 Replies
5. AIX
Hi Admins,
I am new into aix.I was surfing aix pages and reading how to replace failed mirror disks.I read in one of the posts that we have to reboot the server to replace the disk. actually i was a HPUX admin and many times replaced root mirror disk online.Ofcourse it was hot swappable.
... (2 Replies)
Discussion started by: newaix
2 Replies
6. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
7. Solaris
A mirror Raid system with two disk (probabaly raid1: Sun solaris Netra 240)
the following error occured
when I look at it with metastat :
d101: Submirror of d100
State: Needs maintenance
Invoke: metareplace d100 c1t0d0s5 <new device>
is there any advice that it indicates that... (15 Replies)
Discussion started by: xramm
15 Replies
8. Solaris
Hi,
I am running Solaris 8 on Sun server with 2 hard drives. I have configured mirroring on the system using DiskSuite tool in order to have the same data on both disks. Now I want to perform some software upgrade and I would like to use the second disk as a backup disk. This means taking this... (3 Replies)
Discussion started by: carlossg
3 Replies
9. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
10. UNIX for Dummies Questions & Answers
Hi everybody,
I am running SCO-V openserver platform running on P-100.
How can I replace root / boot files ? I want to do this because, if my system is not getting booted or my root is corrupted, I want to just replace this with the back up taken or boot/root floppy. Usually I am restoring... (1 Reply)
Discussion started by: skant
1 Replies