9 More Discussions You Might Find Interesting
1. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
2. Filesystems, Disks and Memory
Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX (1 Reply)
Discussion started by: ivan.estay
1 Replies
3. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
4. Solaris
hi all,
i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx (4 Replies)
Discussion started by: lid-j-one
4 Replies
5. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
6. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
7. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
9. UNIX for Advanced & Expert Users
Hi all..
I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas?
I dont want to remove the wrong disk :)
thanks in advance.. (3 Replies)
Discussion started by: s93366
3 Replies
AMTAPE(8) System Administration Commands AMTAPE(8)
NAME
amtape - Control Amanda changers
SYNOPSIS
amtape [-o configoption...] config subcommand [subcommand_options...]
DESCRIPTION
Amtape is the command-line interface to Amanda's tape changers (amanda-changers(7)) and to the taperscan algorithm (amanda-taperscan(7)).
Tape changers maintain a notion of the current slot for each configuration. This may or may not correspond to an actual physical state of
the device, but is used by some taperscan algorithms to minimize searching through the slots.
Amtape uses the default changer. To use a different changer, use the config override option, e.g., -otpchanger=otherchanger.
SUBCOMMANDS
label label
Search for and load the Amanda tape with label [label], also setting the current slot.
slot slot
Load the volume in the given slot, also setting the current slot. The slot names current, next, first, and last have special meaning.
current
Shorthand for slot current.
inventory
Show the contents of all slots, based on the changer's cached metadata. This is a quick operation as it does not load or unload any
volumes, but is not supported by all changers.
show [slots]
Show the contents of all slots (or listed slots) by loading each slot and reading its label. This can be very slow. The slots arguments
is of the form 1,3-5,7.
reset
Reset the changer to a known state. This subcommand is intended to clear any unknown and potentially incorrect state the changer may
have stored.
eject [drive]
Eject the tape currently in the drive. This only applies to some changers. Specify a drive (by drive number) if more than one drive is
available.
clean [drive]
If a cleaning tape is defined for the changer, used it to clean the specified drive. The [drive] is optional if the changer only has
one drive.
taper
Run the taperscan algorithm (see amanda-taperscan(7)), displaying information about the progress of the scan.
update [what]
Update changer state. Consult amanda-changers(7) for changer-specific details on the format of what.
-o configoption
See the "CONFIGURATION OVERRIDE" section in amanda(8).
SEE ALSO
amanda(8), amanda-changers(7), amanda-taperscan(7), amanda-devices(7)
The Amanda Wiki: : http://wiki.zmanda.com/
AUTHORS
Dustin J. Mitchell <dustin@zmanda.com>
Zmanda, Inc. (http://www.zmanda.com)
James da Silva <jds@amanda.org>
Stefan G. Weichinger <sgw@amanda.org>
Amanda 3.3.3 01/10/2013 AMTAPE(8)