d1000 or minipac with six disk slot

9 More Discussions You Might Find Interesting

1. Solaris

D1000 Storedge array connection

I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system. Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal. Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules Oct 13 22:22:02 brampton...

2. Filesystems, Disks and Memory

cantidad de slot de memoria

Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX

3. Solaris

connection problem with Storedge D1000

Hi, Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following : #devfsadm (nothing showed up) #format (no new disk is shown here) i tried this process again after putting ON the...

4. Solaris

AGP slot in my server ?

hi all, i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx

5. Solaris

Storedge D1000 sharing disks between two boxes

Hello, I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks. It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused! So,...

6. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting...

7. Solaris

probe-scsi-all hangs probing D1000

Hi folks, I�m having a problem with a Ultra60 box with diff scsi pci card conected to one D1000. The conection are correct because a checked the D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all disks one time then the led of one of the disks powers off and then nothing...

8. UNIX for Dummies Questions & Answers

bad pci slot?

Hi, im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the...

9. UNIX for Advanced & Expert Users

device - > slot

Hi all.. I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas? I dont want to remove the wrong disk :) thanks in advance..

LEARN ABOUT DEBIAN

amtape

AMTAPE(8)						  System Administration Commands						 AMTAPE(8)

NAME

       amtape - Control Amanda changers

SYNOPSIS

       amtape [-o configoption...] config subcommand [subcommand_options...]

DESCRIPTION

       Amtape is the command-line interface to Amanda's tape changers (amanda-changers(7)) and to the taperscan algorithm (amanda-taperscan(7)).

       Tape changers maintain a notion of the current slot for each configuration. This may or may not correspond to an actual physical state of
       the device, but is used by some taperscan algorithms to minimize searching through the slots.

       Amtape uses the default changer. To use a different changer, use the config override option, e.g., -otpchanger=otherchanger.

SUBCOMMANDS

       label label
	   Search for and load the Amanda tape with label [label], also setting the current slot.

       slot slot
	   Load the volume in the given slot, also setting the current slot. The slot names current, next, first, and last have special meaning.

       current
	   Shorthand for slot current.

       inventory
	   Show the contents of all slots, based on the changer's cached metadata. This is a quick operation as it does not load or unload any
	   volumes, but is not supported by all changers.

       show [slots]
	   Show the contents of all slots (or listed slots) by loading each slot and reading its label. This can be very slow. The slots arguments
	   is of the form 1,3-5,7.

       reset
	   Reset the changer to a known state. This subcommand is intended to clear any unknown and potentially incorrect state the changer may
	   have stored.

       eject [drive]
	   Eject the tape currently in the drive. This only applies to some changers. Specify a drive (by drive number) if more than one drive is
	   available.

       clean [drive]
	   If a cleaning tape is defined for the changer, used it to clean the specified drive. The [drive] is optional if the changer only has
	   one drive.

       taper
	   Run the taperscan algorithm (see amanda-taperscan(7)), displaying information about the progress of the scan.

       update [what]
	   Update changer state. Consult amanda-changers(7) for changer-specific details on the format of what.

       -o configoption
	   See the "CONFIGURATION OVERRIDE" section in amanda(8).

SEE ALSO

       amanda(8), amanda-changers(7), amanda-taperscan(7), amanda-devices(7)

       The Amanda Wiki: : http://wiki.zmanda.com/

AUTHORS

       Dustin J. Mitchell <dustin@zmanda.com>
	   Zmanda, Inc. (http://www.zmanda.com)

       James da Silva <jds@amanda.org>

       Stefan G. Weichinger <sgw@amanda.org>

Amanda 3.3.1							    02/21/2012								 AMTAPE(8)

UNIX for Advanced & Expert Users