8 More Discussions You Might Find Interesting
1. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
3. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
4. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
5. AIX
Hello everyone
I have a problem with one of my drives in an aix box. The library is a 3583 and Aix is 5.3 TL9
The problem was that the fibre channel not work and I change the fibre but when I logging to the aix box I got this in the rmt3
lsdev | grep rmt
rmt0 Available 03-08-00-6,0... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
6. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
8. AIX
Hello all,
I have just installed an HP dat72 external tape drive to an IBM 275 Intellistation (AIX 5L). It was installed as an Other SCSI Tape Drive (rmt1). I am using the Web Based System Manager at this point to do an initial backup
of a journaled file system. I am getting an error and am... (1 Reply)
Discussion started by: joeweisser
1 Replies
tms(4) Kernel Interfaces Manual tms(4)
Name
tms - TMSCP magnetic tape interface
Syntax
For UNIBUS, Q-bus:
controller klesiu0 at uba0
controller uq0 at klesiu0 csr 0174500 vector uqintr
tape tms0 at uq0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 3
For VAXBI:
controller klesib0 at vaxbi0 node 0
controller uq0 at klesib0 vector uqintr
tape tms0 at uq0 drive 0
controller aie0 at vaxbi? node?
controller bvpssp0 at aie0 vector bvpsspintr
tape tms0 at bvpssp0 drive 0
For MSI Bus:
adapter msi0 at nexus?
controller dssc0 at msi0 msinode 0
tape tms0 at dssc0 drive 0
For VAX CI/HSC:
adapter ci0 at nexus?
adapter ci0 at vaxbi? node?
controller hsc0 at ci0 cinode 6
tape tms0 at hsc0 drive 3
Description
Prior to Version 2.0, this device was referenced by tmscp(4).
The TMSCP driver provides a standard tape drive interface, as described in This is a driver for any controller that adheres to the Tape
Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed the Tape
Mass Storage Control Protocol. This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape
drives). See for further details.
Tape Support
TK50, TK70, TF70, TU81, TU81e, TA78, TA79, TA81, RV20, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tms(4)