8 More Discussions You Might Find Interesting
1. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
3. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
4. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
5. AIX
Hello everyone
I have a problem with one of my drives in an aix box. The library is a 3583 and Aix is 5.3 TL9
The problem was that the fibre channel not work and I change the fibre but when I logging to the aix box I got this in the rmt3
lsdev | grep rmt
rmt0 Available 03-08-00-6,0... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
6. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
8. AIX
Hello all,
I have just installed an HP dat72 external tape drive to an IBM 275 Intellistation (AIX 5L). It was installed as an Other SCSI Tape Drive (rmt1). I am using the Web Based System Manager at this point to do an initial backup
of a journaled file system. I am getting an error and am... (1 Reply)
Discussion started by: joeweisser
1 Replies
tz(4) Kernel Interfaces Manual tz(4)
Name
tz - SCSI magnetic tape interface
Syntax
VAX NCR 5380:
adapter uba0 at nexus?
controller scsi0 at uba0 csr 0x200c0080 vector szintr
tape tz0 at scsi0 drive 0
VAX DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC KZQ:
adapter uba0 at nexus?
controller kzq0 at ibus? csr 0761300vector sii_intr
tape tz0 at kzq0 drive 0
RISC NCR ASC:
adapter ibus0 at nexus?
controller asc0 at ibus? vector ascintr
tape tz0 at asc0 drive 0
Description
The SCSI tape driver provides a standard tape drive interface as described in This is a driver for any Digital SCSI tape device.
For the TZK10 QIC format tape drive, the densities supported are QIC-24 (read only) block size of 512 byte blocks, QIC-120, and QIC-150
read/write block size of 512 byte blocks, and QIC-320 read/write block size of 1024 byte blocks. With QIC format style tapes all reads and
writes must be in multiple of the block size. This is a requirement of fixed block tape drives because record boundaries are not pre-
served. The QIC densities are selected using the following special device names:
QIC-24 Fixed block size.
QIC-120 Fixed block size.
QIC-150 Fixed block size.
QIC-320 Fixed block size.
With all fixed block tape devices a of a file to the tape must be padded out. An example of this is a of which has a size of approximately
3800 bytes.
dd if=/etc/gettytab of=/dev/rmt0h bs=10k conv=sync
or
dd if=/etc/gettytab of=/dev/rmt0l bs=512 conv=sync
The option of pads the output to block size.
This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape drives). See for further
details.
Tape Support
TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), SCSI(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tz(4)