9 More Discussions You Might Find Interesting
1. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
2. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
3. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
4. Red Hat
Dear experts,
Can any one suggest, whether RHEL is supported in HP NetServer LH6000 U3
Thanks (2 Replies)
Discussion started by: ./hari.sh
2 Replies
5. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
6. UNIX for Dummies Questions & Answers
This server had an HP C1555 tape drive that appears to have gone belly up. We found a replacement, an HP C1537, that we want to install. We did the hardware thing, with power off, of course, but when the box was rebooted it did not seem to recognize the drive. At least the backup software did... (4 Replies)
Discussion started by: akirson
4 Replies
7. UNIX for Dummies Questions & Answers
I tried to install SCO Open Server on HP2000 U3
drivers is amrid,
at install of SCO unnix only recognize non hot plugged devices
I have 2 HD of 40 GO under ID 0 and 1 but unix does not see them at boot ?? (1 Reply)
Discussion started by: Bernardschmitt
1 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have a SCO Openserver 5.0.5 server running RAID5 on the hp NETRAID-1M controller and it works just fine.
However, I cannot add a tape drive in. The standard SCSI card is a Symbios and I am using the 'slha' driver, but the system doesnt see the adaptor at SCO startup. The adaptor and... (1 Reply)
Discussion started by: christate
1 Replies
9. UNIX for Dummies Questions & Answers
Over the past few weeks i've installed Red Hat 7.1 on an HP LPR Netserver and everytime i've installed it, I get errors on the drives and it keeps having me run the fsck command and i suspect that its the scsi drivers, everytime you reboot it gets worse and eventually will no longer boot. I've... (3 Replies)
Discussion started by: Lyghtnin
3 Replies
IIR(4) BSD Kernel Interfaces Manual IIR(4)
NAME
iir -- Intel Integrated RAID controller and ICP Vortex driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device pci
device scbus
device iir
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iir_load="YES"
DESCRIPTION
The iir driver claims to interface with the Intel integrated RAID controller cards, and all versions of the ICP Vortex controllers (including
FC).
HARDWARE
Controllers supported by the iir driver include:
o Intel RAID Controller SRCMR
o Intel Server RAID Controller U3-l (SRCU31a)
o Intel Server RAID Controller U3-1L (SRCU31La)
o Intel Server RAID Controller U3-2 (SRCU32)
o All past and future releases of Intel and ICP RAID Controllers.
o Intel RAID Controller SRCU21 (discontinued)
o Intel RAID Controller SRCU31 (older revision, not compatible)
o Intel RAID Controller SRCU31L (older revision, not compatible)
The SRCU31 and SRCU31L can be updated via a firmware update available from Intel.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The iir driver is supported and maintained by Achim Leubner <Achim_Leubner@adaptec.com>.
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org> and is based on information supplied by the driver authors and the website
of Mike Smith <msmith@FreeBSD.org>.
BSD
August 8, 2004 BSD
