8 More Discussions You Might Find Interesting
1. AIX
Hi,
This is follow up to the post https://www.unix.com/aix/233361-san-disk-appearing-double-aix.html
When I connected Pseries Machine HBA Card ( Dual Port ) directly to the SAN Storage DS4300 , I was able to see Host Port Adapter WWN numbers , although I was getting this message... (2 Replies)
Discussion started by: filosophizer
2 Replies
2. AIX
Hello everyone
I would like to hear your opinions about Aix 6.1 and Aix 5.3 with Storage Hitachi the model is USP VM.
We buy it and I want to know day to day task with this storage and Aix.
Thanks for your comments.
Best wishes for this 2010 (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
3. AIX
Host Name - xxxxxxx
IP Address - xxxxxxxxx
Alert Msg - The percentage of available storage space (DMXMemory) is low (49.54374442289481 percent).
Time received - 14:23
Time Logged - 14:55
Suggested Group - MR-UNIX (5 Replies)
Discussion started by: Nyiko
5 Replies
4. AIX
Hi Guys,
It's me again with this unending support of AIX43 ML 9.
I finally able to test a migration from SSA to SAN, no problem. One problem, I bought some expansion of DS4300, two arrays. The IBM tech told me that before I can connect to the existing DS4300, I need to upgrade the firmware... (1 Reply)
Discussion started by: itik
1 Replies
5. AIX
hi,
i'm new to this company and i'm using old AIX 4.3 with DAS and SSA storage. What is the best way to query a report for disk capacity, usage, free, etc.
I know in AIX 5 there's a command for "du -g /" or "du -m /" to report the total usage but I'm not using AIX5. In AIX 4.3 I can use "df... (5 Replies)
Discussion started by: venerayan
5 Replies
6. AIX
Hi,
How do I query for unused partition in AIX 4.3 with DAS and SAA storage?
I know most unix administrator don't put all the capacity on the system at once.
thanks,
vene (1 Reply)
Discussion started by: venerayan
1 Replies
7. AIX
Hi:-
What is the best way to determine what type of storage is attached to an AIX server?
Thanks, (2 Replies)
Discussion started by: janet
2 Replies
8. Filesystems, Disks and Memory
Hello,
We're setting up a solution for a group of customers with 2 p520 servers and 1 DS4300 unit with 9 disks (at this stage). The meaning is to create two arrays on the DS4300. Both servers will be connected to the DS4300 unit and to both controllers (e.g. Controller 1 connected to server 1... (0 Replies)
Discussion started by: EricBE
0 Replies
ICP(4) BSD Kernel Interfaces Manual ICP(4)
NAME
icp -- ICP-Vortex and Intel Storage RAID driver
SYNOPSIS
icp* at pci? dev ? function ?
ld* at icp? unit ?
icpsp* at icp? unit ?
scsibus* at icpsp?
DESCRIPTION
The icp driver provides support for the newer (post 1997) ICP-Vortex GDT and Intel Storage RAID controllers.
The ld driver provides access to logical devices (disk arrays) presented by the controller. The icpsp driver provides direct access to other
SCSI devices attached to the controller, such as tape or CD-ROM drives.
DIAGNOSTICS
pci_mem_find: expected mem type 00000000, found 00000002
This message may be displayed during autoconfiguration if the controller's memory is mapped below 1MB in physical address
space. This can be disabled either through changing a setting in the controller's BIOS utility, or changing the position of a
jumper on the board. See your controller's documentation for more information.
SEE ALSO
intro(4), ld(4), scsi(4)
HISTORY
The icp driver first appeared in NetBSD 1.6, and was based on the FreeBSD and OpenBSD drivers of the same name.
BUGS
ISA & EISA front-ends and a management interface are needed.
Older PCI boards are not yet supported.
BSD
April 20, 2002 BSD