8 More Discussions You Might Find Interesting
1. Post Here to Contact Site Administrators and Moderators
Hello MODs/Admins,
Could you please help me here as from last 6 to 7 days I(and checked with my fellow friends too) am not able to access unix.com site at all. It is very very slow, it never loads completely. Even I checked with different people and different computers it results same only,... (8 Replies)
Discussion started by: RavinderSingh13
8 Replies
2. Proxy Server
Dear all experts here,
:)
I would like to install a proxy server on Linux server to perform solely to control the access of Web server.
In this case, some of my vendor asked me to try Squid and I have installed it onto my Linux server.
I would like know how can I set the configuration to... (1 Reply)
Discussion started by: kwliew999
1 Replies
3. IP Networking
Hi all
I need help with a set of iptables rules that would allow a portion of a bank of ipaddresses acces to only one or two named wbsites.
Please advise
Thank You
Ed (3 Replies)
Discussion started by: wa1ed
3 Replies
4. Emergency UNIX and Linux Support
I need a Squid config that allows access to only one domain: .example.com
Traffic should only be allowed through if coming from 10.100.0.0/24
and only port 80 (http) and port 443 (https) traffic should be allowed through, but again, only to this ONE domain.
It Must be Squid (no iptables... (3 Replies)
Discussion started by: glev2005
3 Replies
5. IP Networking
Hello,
I have a pretty useless satellite link at home (far from any civilization), so I wanted to set up caching in order to speed things up. My Squid 2.6 runs "3128 transparent" and is set up quite well on a separate machine.
I also have my dd-wrt router to move all port 80 traffic through... (0 Replies)
Discussion started by: theWojtek
0 Replies
6. Emergency UNIX and Linux Support
Hi all
We have squid-2.5.STABLE11-3.FC4 running in our environment.
LDAP authentication works fine. Active Directory 2003 Users are prompted to enter credentials every time they access the net. The system works perfectly, but I need to configure Squid to block users in a specific AD group.... (1 Reply)
Discussion started by: wbdevilliers
1 Replies
7. UNIX and Linux Applications
Hi ,
I am new user.
As you know when acl is defined in /etc/squid/squid.conf file according to its http_access users are able to access internet.
Before that .htaccess asks them to access internet.
It is fine.
I saw in some customised linux servers in place of .htaccess login ,html web page... (1 Reply)
Discussion started by: sandeepvson
1 Replies
8. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
uusnap(1M) uusnap(1M)
NAME
uusnap - show snapshot of the UUCP system
SYNOPSIS
DESCRIPTION
The commands, including are targeted for removal from HP-UX; see the below.
displays in tabular format a synopsis of the current UUCP situation. The format of each line is as follows:
site N Cmds N Data N Xqts Message
Where site is the name of the site with work, N is a count of each of the three possible types of work (command, data, or remote execute),
and Message is the current status message for that site as found in the file.
Included in Message may be the time left before UUCP can re-try the call, and the count of the number of times that UUCP has tried to reach
the site. The process id of may also be shown if it is in a TALKING state.
WARNINGS
Use of commands, including is discouraged because they are targeted for removal from HP-UX. Use ftp(1) or rcp(1) instead.
AUTHOR
was developed by the University of California, Berkeley.
SEE ALSO
uucp(1).
Tim O'Reilly and Grace Todino,
O'Reilly & Associates, Inc. USA.
Grace Todino and Dale Dougherty,
O'Reilly & Associates, Inc. USA.
TO BE OBSOLETED uusnap(1M)
