9 More Discussions You Might Find Interesting
1. Linux
I have created a bridge with nmcli between eth0 and wlan0
I use this procedure
sudo nmcli con add ifname br0 type bridge con-name br0
sudo nmcli con add type bridge-slave ifname eth0 master br0
sudo nmcli con add type bridge-slave ifname wlan0 master br0
sudo nmcli con modify br0... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
2. Debian
Dear Moderator,
While working on airmon-ng when the situation has come to set wlan0 on monitor mode
Identification Wlan0
root@kali:~# iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated ... (1 Reply)
Discussion started by: raghunsi
1 Replies
3. Red Hat
Hi All,
Am using Toshiba Satellite C850-l5212 Laptop . I have installed RHEL6 server on it ( Linux 2.6.32-220.el6.x86_64 )
I Installed wireless driver ( linux_mac80211_0012.0207.2013.tar.bz2 ) and the installation went fine.
But when i do ifconfig wlan0 up its giving the below error .... (0 Replies)
Discussion started by: senthilcaesar
0 Replies
4. Debian
Hi I'm getting some troubles trying to create a Debian wheeze 7 from a vm using VMware from a laptop which I get lan and internet connection by a wireless router.
The first problem is that I'm a bit lost trying to configure the wlan to get lan and internet connection.
I've read about that I gotta... (2 Replies)
Discussion started by: adiegorpc
2 Replies
5. UNIX for Dummies Questions & Answers
Hello everyone.
I am trying to do a parallel computation and the computation continues for like an hour and then it stops with the error:
slurmd: *** JOB 785385 CANCELLED AT 2012-02-08T20:18:42 DUE TO TIME LIMIT ***
Please can anyone tell me what is going on and how to fix the error...I... (0 Replies)
Discussion started by: lebphys78
0 Replies
6. UNIX for Dummies Questions & Answers
We have an application that uses Active directory to authenticate the users. the admins of the app. were complaining because the windows domain controller they are going against is not very stable. I wrote a shell script using ldapsearch to look up a user against the domain controller their app... (2 Replies)
Discussion started by: jayjabour
2 Replies
7. Shell Programming and Scripting
Hello Folks,
I have been asked to write a test script which can be run by students. the script should have a time limit.
I have almost completed it except the bit of timing!
I've seen something like this:
on_timeout()
{
echo "$USER $score " >> theresult.txt
echo "Time out!... (2 Replies)
Discussion started by: SultanKSA
2 Replies
8. AIX
Hello, we had a situation where an account was locked out due to too many failed login attempts. From the logs (failedlogin, etc) it appears that AIX 'remembered' the failed login attempts from the past month or so. does anyone know where this is set, or how long it will remember the number of... (2 Replies)
Discussion started by: zuessh
2 Replies
9. UNIX for Dummies Questions & Answers
How do I limit the amount of idle time an account gets on solaris?
Thanks.
VJ (2 Replies)
Discussion started by: vancouver_joe
2 Replies
WPI(4) BSD Kernel Interfaces Manual WPI(4)
NAME
wpi -- Intel 3945ABG Wireless LAN IEEE 802.11 driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device wpi
device wpifw
device pci
device wlan
device wlan_amrr
device firmware
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_wpi_load="YES"
DESCRIPTION
The wpi driver provides support for the Intel 3945ABG Wireless network adapter wpi supports station, adhoc, and monitor mode operation. Only
one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8).
This driver requires the firmware built with the wpifw module to work.
FILES
/usr/share/doc/legal/intel_wpi/LICENSE wpi firmware license
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan0 create wlandev wpi0 inet 192.168.0.20
netmask 0xffffff00
Join a specific BSS network with network name ``my_net'':
ifconfig wlan0 create wlandev wpi0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan0 create wlandev wpi0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
Join a specific BSS network with 128-bit WEP encryption:
ifconfig wlan0 create wlandev wpi0 wlanmode adhoc ssid my_net
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1
DIAGNOSTICS
wpi%d: could not load firmware image '%s' The driver failed to load the firmware image using the firmware(9) subsystem. Verify the wpifw
firmware module is installed.
wpi%d: fatal firmware error An unknown error has occurred in the uploaded firmware, you may have to unload/reload the driver to continue.
wpi%d: Radio transmitter is switched off The hardware switch controlling the radio is currently turned off. Data transmission is not possi-
ble in this state.
BUGS
Not all the error messages are documented here.
Background scanning is not currently supported.
SEE ALSO
wpifw(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8).
AUTHORS
The original wpi driver was written for OpenBSD by Damien Bergamini <damien.bergamini@free.fr>. Benjamin Close <benjsc@FreeBSD.org> ported
wpi to FreeBSD.
BSD
October 5, 2008 BSD