10 More Discussions You Might Find Interesting
1. Solaris
Hi all
I have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore.
backup was taken... (0 Replies)
Discussion started by: nikhil kasar
0 Replies
2. Solaris
hi all
i have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore. (3 Replies)
Discussion started by: nikhil kasar
3 Replies
3. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
4. Solaris
Hi All,
I have rootdg encapsulated within Veritas Volume Manager.
/# vxprint -vg rootdg
TY NAME ASSOC KSTATE LENGTH PLOFFS STATE TUTIL0 PUTIL0
v rootvol root ENABLED 24585216 - ACTIVE - -
v swapvol swap ENABLED 20484288 -... (3 Replies)
Discussion started by: solaris_1977
3 Replies
5. Solaris
Hi all,
How to i use vxfs for my server? Because when i install OS, it is installed with ufs, then after Solaris 10 installation, i proceed to install vxfs.
How do i convert all the ufs to vxfs? Or is it what i'm doing is the incorrect way?
Please help. :wall: (9 Replies)
Discussion started by: beginningDBA
9 Replies
6. Solaris
Hi,
I have 2 hosts with Veritas VxVM and VxFS (5.0 MP3_RP2). I need to use the application filesystem's luns from these 2 hosts and mount it on another 2 hosts that are running Solaris 9 09/05 and SVM.
Is there resources online or has someone tried this? (4 Replies)
Discussion started by: xor
4 Replies
7. Solaris
what is the difference between VXVM and SVM ?
What is the advantages of VXVM over SVM ?
thanks (2 Replies)
Discussion started by: sijocg
2 Replies
8. Solaris
How to find & replace bad disks in solaris & VXVM?plz
explain step by step? (2 Replies)
Discussion started by: xtreams
2 Replies
9. Solaris
hi guys,
I am studying for the solaris scsa and i want to practice with ufsdump and restores, fssnaps etc...
my question is, i finally found a server with a tape drive attached that i can mess arouund with because its not a critical box.
its running solaris 8, and i want to do a ufsdump, but... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
10. UNIX for Advanced & Expert Users
Hello ! :confused:
Does anyone knows anything about procedure to convert Solaris UFS filesystem to VxFS.
Thx,
Witt (1 Reply)
Discussion started by: witt
1 Replies
vxiod(1M) vxiod(1M)
NAME
vxiod - start, stop, and report on Veritas Volume Manager I/O threads
SYNOPSIS
vxiod
vxiod [-f ] [set count]
DESCRIPTION
The vxiod utility starts, stops, or reports on Veritas Volume Manager (VxVM) I/O kernel threads. An I/O thread provides a process context
for performing I/O in VxVM.
When the vxio module is loaded, 16 I/O threads are created, plus 2 threads per additional CPU for a system with more than 8 CPUs, up to a
maximum of 64 threads. At least one I/O thread must be running while the vxio module is loaded, and the number of I/O threads cannot be
forced to zero.
When invoked with no arguments, vxiod prints the current number of I/O threads to the standard output.
The number of threads that is required for handling I/O requests depends on the system load and usage. If volume recovery seems to proceed
more slowly at times, it may be possible to improve its performance by increasing the number of I/O threads up to a maximum of 64.
KEYWORDS
set When invoked with the set keyword, vxiod creates the number of I/O threads specified by count. If more volume I/O threads exist
than are specified by count, the excess processes terminate. If more than the maximum number(64) are specified, the requested
number is silently truncated to that maximum.
OPTIONS
-f This option has no effect from release 5.0 onward. The number of I/O threads cannot be reduced to zero.
EXIT CODES
The vxiod utility prints a diagnostic on the standard error, and exits if an error is encountered. If an I/O request occurs within a I/O
thread, the state of that I/O request is not reflected in the exit status for vxiod. Otherwise, vxiod returns a non-zero exit status on
error.
Usage errors result in an exit status of 1 and a usage message. If the requested number of threads cannot be created, the exit status is
2, and the number of threads that were successfully started is reported. If any other error occurs, the exit status is 3.
FILES
/dev/vx/iod The device used to report on and start volume I/O threads.
NOTES
Veritas Volume Manager I/O threads cannot be killed directly through the use of signals.
Depending on the operating system, VxVM I/O threads may not appear in the list of processes that is output by the ps command. The number
of I/O threads that is currently running can be determined by running vxiod.
SEE ALSO
fork(2), ps(1), vxconfigd(1M), vxdctl(1M), vxintro(1M), vxio(7), vxiod(7)
VxVM 5.0.31.1 24 Mar 2008 vxiod(1M)