Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)
Hi,
I went to a computer store and the salesman sold me a SATA cable and told me that all SATA cables are the same. Another salesman at a different store told me a cable rated for SATA 2, which I bought, MIGHT work as well as one rate for SATA 3 but it is not guaranteed. I decided to run a... (3 Replies)
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
I am trying to find a command to return the "link" speed of the networks installed on AIX.
ifconfig - gives me where the link is up and the duplex setting. I need to determine for example if the ethernet connection is 10, 100, 1000 Mbs or what the current speed is based on the network media... (3 Replies)
NATSEMI-DIAG(8) System Manager's Manual NATSEMI-DIAG(8)NAME
natsemi-diag - EEPROM setup and diagnostic program for ethernet cards based on the National Semiconductor DP83810 / 83815 chips.
SYNOPSIS
natsemi-diag [options]
DESCRIPTION
netsemi-diag is a program that you can use to diagnose problems with ethernet cards based on the National Semiconductor DP83810 / 83815
chips.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-a, --show_all_registers
Print all registers.
-# <cardnum>
Use card number <cardnum>.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --port-base <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII and Autosense.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run natsemi-diag with the options '-t -1'.
SEE ALSO mii-diag(8)AUTHOR
netsemi-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 NATSEMI-DIAG(8)
