natsemi-diag(8) [debian man page]
NATSEMI-DIAG(8) System Manager's Manual NATSEMI-DIAG(8) NAME
natsemi-diag - EEPROM setup and diagnostic program for ethernet cards based on the National Semiconductor DP83810 / 83815 chips. SYNOPSIS
natsemi-diag [options] DESCRIPTION
netsemi-diag is a program that you can use to diagnose problems with ethernet cards based on the National Semiconductor DP83810 / 83815 chips. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -a, --show_all_registers Print all registers. -# <cardnum> Use card number <cardnum>. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --port-base <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run natsemi-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
netsemi-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 NATSEMI-DIAG(8)
Check Out this Related Man Page
VIA-DIAG(8) System Manager's Manual VIA-DIAG(8) NAME
via-diag - EEPROM setup and diagnostic program for the VIA Rhine vt86c100 and vt3043 Ethernet controller chips. SYNOPSIS
via-diag [options] DESCRIPTION
via-diag is a program that you can use to diagnose problems with VIA Rhine vt86c100 and vt3043 Ethernet controller chips. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --base-address <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII, HomePNA and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run via-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
via-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 VIA-DIAG(8)