9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
VLAN(7) Miscellaneous Information Manual VLAN(7)
NAME
VLAN - virtual local area network
DESCRIPTION
This manpage provides a brief overview of VLAN (virtual LAN) technology.
VLANs are logical, or network segments that can span multiple physical network segments. A primary benefit of VLANs is that they can iso-
late broadcast and multicast traffic by determining which destinations should receive that traffic, thereby making better use of switch and
end-station resources.
Logical separation using VLAN allows for the logical grouping of PCs, servers and other network resources to behave as if they were con-
nected to the same, physical segment, even if they are not.
HP-UX VLAN is an implementation of IEEE 802.1p/Q standards.
VLAN interfaces can be configured in HP-UX servers using the command (see nwmgr_vlan(1M)) or (see lanadmin_vlan(1M)). HP recommends that
you use for HP-UX Release 11i Version 3 and forward. Interfaces can also be configured using the web-based management tool HP-UX System
Management Homepage (HP SMH).
Each VLAN interface created is assigned a VLAN PPA (VPPA) that is unique across the system and a VLAN ID, that identifies the virtual LAN
it is part of. The VLAN ID is unique on the interface on which the VLAN interface is created.
WARNINGS
The and commands are deprecated. These commands will be removed in a future HP-UX release. HP recommends the use of replacement command
nwmgr(1M) to perform all network interface-related tasks.
SEE ALSO
lanadmin(1M), lanadmin_vlan(1M), lanscan(1M), nwmgr(1M), nwmgr_vlan(1M), smh(1M).
IEEE 802.1p, IEEE 802.1Q
VLAN(7)