9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
GUESSNET-SCAN(8) System Manager's Manual GUESSNET-SCAN(8)
NAME
guessnet-scan - guess network configuration data by looking at network traffic
SYNOPSIS
guessnet-scan [options] [ethernet_interface]
DESCRIPTION
Guessnet-scan tries to deduce network configuration data by watching network traffic at a given Ethernet interface.
After scanning network traffic for some time, guessnet-scan prints a configuration string suitable for inclusion in /etc/network/inter-
faces.
Note that guessnet-scan uses heuristics and wild guesses and that the resulting data is not guaranteed to be accurate. The program is
intended to be used as a first try at getting network configuration data without bothering anyone.
OPTIONS
Options follow the usual GNU conventions,
--debug
Print debugging messages.
--help Show a brief summary of commandline options.
--init-time=int
Time in seconds to wait for the interface to initialize when it is not found already up at program startup. Default: 3 seconds.
-t, --timeout=int
Time in seconds to watch for network traffic. Default: 5 seconds.
-v, --verbose
Operate verbosely.
--version
Show the version number of the program.
SCANNING REQUIREMENTS
To correctly identify all data of the local network, guessnet-scan needs to see traffic related to a host in the local network and to the
local gateway, if any.
To be able to identify the network gateway, guessnet-scan also needs to see some traffic directed to the external network: you can help the
detection by generating some outbound IP traffic during the scan, for example by browsing a web page (without proxy) or using telnet to
open a connection to some remote host.
Note that if you are connected to a switch, guessnet-scan won't probably be able to work, since the switch will isolate it from the network
traffic that the other machines are generating.
SEE ALSO
guessnet(8), interfaces(5).
AUTHOR
Guessnet-scan was written by Enrico Zini <enrico@debian.org>.
10 October 2004 GUESSNET-SCAN(8)