9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
net_phygetnext(9F) Kernel Functions for Drivers net_phygetnext(9F)
NAME
net_phygetnext - search through the current list of network interfaces
SYNOPSIS
#include <sys/neti.h>
phy_if_t net_phygetnext(const net_data_t net, const phy_if_t ifp);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI).
PARAMETERS
net value returned from a successful call to net_protocol_lookup(9F).
ifp value returned from a successful call to this function or net_phylookup(9F).
DESCRIPTION
The net_phygetnext() function searches through all of the network interfaces that a network protocol "owns". To start searching through all
of the interfaces owned by a protocol, a value of 0 should be passed through as the value of ifp. When 0 is returned by this function, the
last of the interfaces owned by this protocol has been reached.
When called successfully, the value returned represents a network interface that exists, at the time of the call, within the scope of the
network interface. This value is only guaranteed to be unique for a name within the scope of the network protocol.
EXAMPLES
net_data_t net;
phy_if_t ifp;
char buffer[32];
net = net_protocol_lookup("inet");
if (net != NULL) {
for (ifp = net_phygetnext(net, 0); ifp != 0;
ifp = net_phygetnext(net, ifp)) {
/* Do something with ifp */
if (net_getifname(net, ifp, buffer,
sizeof(buffer) >= 0)
printf("Interface %s0, buffer);
}
}
RETURN VALUES
The net_phygetnext() function returns -1 if it is not supported by the network protocol or 0 if an attempt to go beyond the last network
interface is made. Otherwise, it returns a value representing a network interface.
CONTEXT
The net_phygetnext() function may be called from user, kernel, or interrupt context.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
SEE ALSO
net_phylookup(9F), net_protocol_lookup(9F), attributes(5)
SunOS 5.11 1 May 2008 net_phygetnext(9F)