Visit Our UNIX and Linux User Community


Access to network interface (Mac-network)

 
Thread Tools Search this Thread
Special Forums UNIX and Linux Applications Access to network interface (Mac-network)
# 1  
Old 03-08-2012
Access to network interface (Mac-network)

Hi,

I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

6. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies

7. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies
IZ(8)							  System Administration Utilities						     IZ(8)

NAME
iz - configure an IEEE 802.15.4 interface SYNOPSIS
iz [options] [command] DESCRIPTION
Manage IEEE 802.15.4 network interfaces OPTIONS
-d, --debug[=N] print netlink messages and other debug information -v, --version print version -h, --help print help Common commands: help [command] Print detailed help for a command. event [iface] Monitor events from the kernel (^C to stop). PHY 802.15.4 commands: listphy [phy] List phys(s). add phy [iface] Add an interface attached to specified phy. del [phy] iface Delete the specified interface. MAC 802.15.4 commands: scan <iface> <ed|active|passive|orphan> <channels> <duration> Perform network scanning on specified channels. assoc <iface> <pan> <coord> <chan> ['short'] Associate with a given network via coordinator. disassoc <iface> <addr> <reason> Disassociate from a network. list [iface] List interface(s). AUTHOR
Written by Dmitry Eremin-Solenikov, Sergey Lapin and Maxim Osipov REPORTING BUGS
Report bugs to linux-zigbee-devel@lists.sourceforge.net Userspace tools for Linux IEEE 802.15.4 stack homepage <http://linux-zigbee.sourceforge.net/> COPYRIGHT
Copyright (C) 2008, 2009 by Siemens AG License GPLv2 GNU GPL version 2 <http://gnu.org/licenses/gpl.html>. This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. iz 0.2.2 August 2010 IZ(8)

Featured Tech Videos