9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
vtdaemon(1M) vtdaemon(1M)
NAME
vtdaemon - respond to vt requests
SYNOPSIS
lan_device lan_device ...
DESCRIPTION
responds to requests from other systems (via local area network) made by (see vt(1)). spawns a server to respond to each request that it
receives.
Options
recognizes the following command-line options and arguments:
Causes to rebroadcast all requests received on one lan device to all other lan devices specified on the command line. The
optional parameter ngateway specifies the maximum number of vtgateway servers that can be in operation concurrently. If
ngateway is not specified, there is no limit on the number of vtgateway servers that can be in operation concurrently.
Causes vtdaemon to ignore all requests that have come through a gateway.
The remaining arguments are the full path names of lan devices that vtdaemon looks for requests on. If no lan devices are specified, the
default lan device is used.
The major number for this device must correspond to a IEEE 802.3 local area network device.
Another function of is to create portals and service portal requests. A portal is a callout device that can be used by to communicate to
another machine via local area network (see uucico(1M)). Portals are created by according to the configuration information found in the
file Each line in has the format:
<calldev>[,<lan device>] <nodename>
For each line, creates a portal named calldev in Whenever this device is opened, spawns a server that creates a connection to the system
specified by nodename via the lan device specified. If no lan device is specified, the first one specified on the command line when was
started is used (or the default lan device is used if no lan devices were specified on the command line).
should be terminated by sending signal to it. When receives this signal it removes all of the portals it created in before exiting.
DIAGNOSTICS
Diagnostics messages produced by are written to
WARNINGS
uses the Hewlett-Packard (Link Level Access) direct interface to the HP network drivers. uses the multicast address It should not be used
or deleted by other applications accessing the network. uses the following IEEE 802.3 sap (service access point) values: and They should
not be used by other applications accessing the network.
Desktop HP-UX
If your system has been installed with the Desktop HP-UX product, then both and will not be started by default. In order to start these
daemons, change PTYDAEMON_START and VTDAEMON_START from a "0" to a "1" in the and files, respectively. The system must either be rebooted
for these changes to take effect, or you can manually start both daemons by typing :
where /dev/lan0 is the character special device file corresponding to the IEEE802.3 local area network device.
FILES
logfile used by vtdaemon.
default lan device name.
SEE ALSO
vt(1), uucico(1M).
vtdaemon(1M)
