I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
gateways(4) Kernel Interfaces Manual gateways(4)NAME
gateways - Specifies Internet routing information to the routed daemon
SYNOPSIS
/etc/gateways
DESCRIPTION
The /etc/gateways file identifies gateways for the routed daemon. Ordinarily, the routed daemon queries the network and builds routing
tables. The routed daemon builds the tables from routing information transmitted by other hosts directly connected to the network. How-
ever, there may be gateways that this command cannot identify through its queries. These unidentified gateways are known as distant gate-
ways. Such gateways should be identified in the /etc/gateways file, which the routed daemon reads when it starts.
The general format of an file entry in the /etc/gateways file is: Destination Name1 gateway Name2 metric Value Type
The following is a brief description of each element in an /etc/gateways file entry: A keyword that indicates whether the route is to a
network or to a specific host. The two possible keywords are net and host. The name associated with Destination. Name1 can be either a
symbolic name (as used in the /etc/hosts or /etc/networks file) or an Internet address specified in dotted-decimal format. An indicator
that the following string identifies the gateway host. The name or address of the gateway host to which messages should be forwarded. An
indicator that the next string represents the hop count to the destination host or network. The hop count, or number of gateways, from the
local network to the destination network. A keyword that indicates whether the gateway should be treated as active, passive, or external.
The three possible keywords are as follows: An active gateway is treated like a network interface. That is, it is expected to exchange RIP
(Routing Information Protocol) routing information. Information about it is maintained in the internal routing tables as long as it is
active and is included in any routing information that is transmitted through RIP. If it does not respond for a period of time, the route
associated with it is deleted from the internal routing tables. A passive gateway is not expected to exchange RIP routing information.
Information about it is maintained in the routing tables indefinitely and is included in any routing information that is transmitted
through RIP. An external gateway is identified to inform the routed daemon that another routing process will install such a route and that
alternative routes to that destination should not be installed. Information about external gateways is not maintained in the internal rout-
ing tables and is not transmitted through RIP.
Note that these routes must be to networks.
EXAMPLES
To specify a route to a network through a gateway host with an entry in the gateways file, enter: net net2 gateway host4 metric 4 passive
This example specifies a route to a network, net2, through the gateway host4. The hop count metric to net2 is 4, and the gateway is
treated as passive. To specify a route to a host through a gateway host with an entry in the gateways file, enter: host host2 gate-
way host4 metric 4 passive
This example specifies a route to a host, host2, through the gateway host4. The hop count metric to host2 is 4, and the gateway is
treated as passive. To specify a route to a host through an active Internet gateway with an entry in the gateways file, enter: host
host10 gateway 192.100.11.5 metric 9 active
This example specifies a route to a specific host, host10, through the gateway 192.100.11.5. The hop count metric to host10 is 9 and
the gateway is treated as active. To specify a route to a host through a passive Internet gateway with an entry in the gateways
file, enter: host host10 gateway 192.100.11.5 metric 9 passive
This example specifies a route to a specific host, host10, through the gateway 192.100.11.5. The hop metric count to host10 is 9
and the gateway is treated as passive. To specify a route to a network through an external gateway, enter a line in the following
format: net net5 gateway host7 metric 11 external
This example specifies a route to a network, net5, through the gateway host7. The hop count metric to net5 is 11 and the gateway is
treated as external (that is, it is not advertised through RIP, but is advertised through an unspecified routing protocol).
RELATED INFORMATION
Daemons: gated(8), routed(8) delim off
gateways(4)