10 More Discussions You Might Find Interesting
1. Red Hat
Hi
We are planning to migrate to a new SAN storage environment. Our RHEL5.5 servers boot over SAN.
1. I was wondering if using "lvm mirroring" or "pvmove" would be a solution.
2. Do they do block level transfer?
Thanks (1 Reply)
Discussion started by: ikn3
1 Replies
2. AIX
i'm trying to burn an DVD ISO into a VIOS virtual optical drive
when i try a scanbus i have a failure message :
Can u help me please guys
---------- Post updated at 03:38 PM ---------- Previous update was at 12:20 PM ----------
I can't burn in ISO format, so i have to type... (0 Replies)
Discussion started by: Tharsan
0 Replies
3. Red Hat
We have a RHEL 5.8 server at the production level and we have a Java application on this server. I know of the SSL certificate generation at the OS (RHEL) level but it is implemented on the Java application by our development team using the Java keytool. My doubt is that is the SSL generation can... (3 Replies)
Discussion started by: RHCE
3 Replies
4. Hardware
In general terms what are the differences platform driver,codec driver and Machine driver? (1 Reply)
Discussion started by: rupeshkp728
1 Replies
5. UNIX for Advanced & Expert Users
Can anybody get me some sample driver code of linux block drivers to send request to scsi disks?
Basically I need a sample code of linux scsi block driver.
I tried googling for sample code but did not find it. (1 Reply)
Discussion started by: rupeshkp728
1 Replies
6. Ubuntu
How to end the request(I/O) in block driver for particular disk drive without affecting other request intended for some other drives. (1 Reply)
Discussion started by: coeteam
1 Replies
7. Linux
Hi All,
I am writing a block driver for a 2GB SD card where i get the total amount of data per request as follows:
struct request *req;
uint card_addr,total_bytes;
struct request_queue *rq = BlkDev->queue;
req = elv_next_request(rq);
..
..
card_addr = req->sector*512;... (1 Reply)
Discussion started by: amio
1 Replies
8. Solaris
what are the major Difference Between run level & init level (2 Replies)
Discussion started by: rajaramrnb
2 Replies
9. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
10. Solaris
I've been researching minimizeing Solaris 8 and found that on the web page http://www.sun.com/bigadmin/content/packagelist/s8u7PkgList/p2.html the package SUNWglmr
is listed as "rasctrl environment monitoring driver for i2c, (Root) (32-bit)" while in the document "Solaris 8 minimize-updt1.pdf"... (1 Reply)
Discussion started by: roygoodwin
1 Replies
TAPSET::SCSI(3stap) TAPSET::SCSI(3stap)
NAME
tapset::scsi - systemtap scsi probe points
DESCRIPTION
This family of probe points is used to probe the SCSI activities. It contains the following probe points:
scsi.ioentry
Fires when SCSI mid layer prepares a SCSI request
Arguments:
disk_major
The major number of the disk
disk_minor
The minor number of the disk
device_state
The current state of the device. The possible values could be:
SDEV_CREATED = 1, /* device created but not added to sysfs
* Only internal commands allowed (for inq) */
SDEV_RUNNING = 2, /* device properly configured
* All commands allowed */
SDEV_CANCEL = 3, /* beginning to delete device
* Only error handler commands allowed */
SDEV_DEL = 4, /* device deleted
* no commands allowed */
SDEV_QUIESCE = 5, /* Device quiescent. No block commands
* will be accepted, only specials (which
* originate in the mid-layer) */
SDEV_OFFLINE = 6, /* Device offlined (by error handling or
* user request */
SDEV_BLOCK = 7, /* Device blocked by scsi lld. No scsi
* commands from user or midlayer should be issued
* to the scsi lld. */
scsi.iodispatching
Fires when the SCSI mid layer dispatches a SCSI command to the low level driver
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device.
data_direction
The data_direction specifies whether this command is from/to the device.
The possible values could be:
DMA_BIDIRECTIONAL = 0,
DMA_TO_DEVICE = 1,
DMA_FROM_DEVICE = 2,
DMA_NONE = 3,
request_buffer
The request buffer address
req_bufflen
The request buffer length
scsi.iodone
Fires when a SCSI command is done by low level driver and enqueued into the done queue.
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
scsi.iocompleted
Fires when SCSI mid layer runs the completion processing for block device I/O requests
Arguments:
host_no
The host number
channel
The channel number
lun
The lun number
dev_id
The scsi device id
device_state
The current state of the device
data_direction
The data_direction specifies whether this command is from/to the device.
goodbytes
The bytes completed.
SEE ALSO
stap(1), stapprobes(3stap)
IBM
TAPSET::SCSI(3stap)