Unix and Linux Discussions Tagged with telnet |
|
Thread / Thread Starter |
Last Post |
Replies |
Views |
Forum |
|
|
|
2 |
8,236 |
UNIX for Beginners Questions & Answers |
|
|
|
6 |
16,239 |
UNIX for Beginners Questions & Answers |
|
|
|
8 |
27,962 |
Solaris |
|
|
|
2 |
1,070 |
UNIX for Beginners Questions & Answers |
|
|
|
8 |
3,411 |
UNIX for Beginners Questions & Answers |
|
|
|
1 |
1,023 |
UNIX for Beginners Questions & Answers |
|
|
|
1 |
3,554 |
UNIX for Beginners Questions & Answers |
|
|
|
2 |
3,760 |
AIX |
|
|
|
3 |
3,888 |
Shell Programming and Scripting |
|
|
|
10 |
6,429 |
Shell Programming and Scripting |
|
|
|
7 |
4,183 |
Shell Programming and Scripting |
|
|
|
6 |
7,378 |
AIX |
|
|
|
3 |
4,106 |
AIX |
|
|
|
9 |
18,720 |
Shell Programming and Scripting |
|
|
|
0 |
4,403 |
UNIX for Advanced & Expert Users |
|
|
|
2 |
1,465 |
UNIX for Advanced & Expert Users |
|
|
|
29 |
11,187 |
Shell Programming and Scripting |
|
|
|
6 |
19,621 |
Shell Programming and Scripting |
|
|
|
4 |
3,940 |
Shell Programming and Scripting |
|
|
|
6 |
16,684 |
Shell Programming and Scripting |
|
|
|
2 |
2,897 |
Programming |
|
|
|
2 |
5,255 |
Shell Programming and Scripting |
|
|
|
5 |
2,328 |
Linux |
|
|
|
0 |
2,057 |
IP Networking |
|
|
|
4 |
7,513 |
Solaris |
|
|
|
2 |
6,411 |
Shell Programming and Scripting |
|
|
|
2 |
4,696 |
AIX |
|
|
|
4 |
3,486 |
UNIX for Advanced & Expert Users |
|
|
|
6 |
8,456 |
Shell Programming and Scripting |
|
|
|
12 |
16,683 |
Shell Programming and Scripting |
|
|
|
2 |
11,501 |
AIX |
|
|
|
2 |
5,289 |
Shell Programming and Scripting |
|
|
|
3 |
12,322 |
Linux |
|
|
|
1 |
4,423 |
IP Networking |
|
|
|
8 |
6,636 |
Homework & Coursework Questions |
|
|
|
0 |
2,616 |
Homework & Coursework Questions |
|
|
|
7 |
14,078 |
SCO |
|
|
|
2 |
8,113 |
AIX |
|
|
|
1 |
4,334 |
IP Networking |
|
|
|
0 |
4,543 |
Windows & DOS: Issues & Discussions |
TELNET-PROBE(1) General Commands Manual TELNET-PROBE(1)
NAME
telnet-probe - lightweight telnet-like port probe
SYNOPSIS
$PCP_BINADM_DIR/telnet-probe [-c] [-v] host port
DESCRIPTION
telnet-probe allows the pmdashping(1) daemons to establish connections to arbitrary local and remote service-providing daemons so that
response time and service availability information can be obtained.
The required host and port number arguments have the same meaning as their telnet(1) equivalents.
The -c option causes telnet-probe to perform a connect(2) only. This skips the read(2) and write(2) exercise that would otherwise be done
after connecting (see below).
The -v option causes telnet-probe to be verbose while operating.
Once the telnet connection has been established, telnet-probe reads from stdin until end-of-file, and writes all the input data to the tel-
net connection. Next, telnet-probe will read from the telnet connection until end-of-file, discarding whatever data it receives. Then
telnet-probe exits.
To operate successfully, the input passed via telnet-probe to the remote service must be sufficient to cause the remote service to close
the connection when the last line of input has been processed, e.g. ending with ``quit'' when probing SMTP on port 25.
By default telnet-probe will not produce any output, unless there is an error in which case a diagnostic message can be displayed (in ver-
bose mode only) and the exit status will be non-zero indicating a failure.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the
file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configura-
tion file, as described in pcp.conf(5).
DIAGNOSTICS
If telnet-probe succeeds, then 0 will be returned. If the attempt to establish a connection fails or is terminated, then a non-zero exit
status is returned.
SEE ALSO
PCPintro(1), pmdashping(1), pmie(1), telnet(1), connect(2), read(2) and write(2).
Performance Co-Pilot PCP TELNET-PROBE(1)