9 More Discussions You Might Find Interesting
1. Red Hat
hi everybody,
iam using 32 bit centos 6.2 on my machine. i have purchase TP-LINK, TL-WN727N wireless usb, but i was not able to install on my desktop. i was not able to find drivers for centos 6.2 official site of TPLINK.
$ uname -a
Linux workstation 2.6.32-220.el6.i686 #1 SMP Tue Dec 6... (0 Replies)
Discussion started by: paruhang
0 Replies
2. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
3. Linux
Hi,
I've installed wireless card and I didn't receive any error in the installation process.
Now I want to use it but I can't make internet to work.
if I check my card with iwconfig I get the following message
wlan0 IEEE 802.11g ESSID:"Alice-34376718"
Mode:Managed ... (2 Replies)
Discussion started by: aneuryzma
2 Replies
4. Solaris
Dear All,
i have problem during install modem dial up with smc in solaris 10.
i can't find "login" because it's stop in _receive started transmit started.
thanks for your attention.
this is the list during i dial to this number :
altconn called
Device Type ACU wanted... (0 Replies)
Discussion started by: mr.ridho
0 Replies
5. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
6. Solaris
hi,
can u pls help to configure modem on SUN system for the inbound dialing.....so that i can connect to the system remotely through modem..........thx
girish (2 Replies)
Discussion started by: girish_shukla
2 Replies
7. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
8. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
9. UNIX for Dummies Questions & Answers
I have Linux RedHat7.1 and I have this modem
RockWell HCF 56KDATA Fax PCI Modem.
I don't know how to configure this modem. Can anybody please help me out.
I tried "linuxconf" it does not recognize this command. Pleas help me out.
Regards
-Iftikhar (1 Reply)
Discussion started by: syedifti
1 Replies
FAXSTATE(8) System Manager's Manual FAXSTATE(8)
NAME
faxstate - control ``modem state'' of a device used by HylaFAX
SYNOPSIS
/usr/sbin/faxstate [ -q queue-dir ] [ -s state ] [ -n ] modem
DESCRIPTION
faxstate sends a message to the HylaFAX faxgetty(8) process servicing modem telling it to use the specified state when notifying the
HylaFAX scheduler that a modem is ready and available for use. This is useful for controlling outbound use of a modem; by marking a
modem's state as busy or down the HylaFAX scheduler will not assign any outbound jobs to the modem.
The specified modem can either be the name (typically the last component of the terminal port the modem is attached to), or the full name
of the associated FIFO named pipe file, e.g. ``FIFO.ttym2''.
If the -n option, faxstate emulates what faxgetty would do; sending a message directly to the faxq process marking the specified modem
down, busy, or ready. This interface is useful for send-only environments in which faxgetty processes are not used. Note that modems
manipulated in this way must previously have been configured with the faxmodem(8) program.
OPTIONS
The following options are supported:
-n Contact faxq directly instead of faxgetty.
-q dir Use a spooling area other than /var/spool/hylafax.
-s Specify the state to send the faxq process each time the modem becomes ready for use; one of ``busy'', ``down'', and ``ready''.
The default state to use is ready.
FILES
Consult hylafax-server(5) for a complete discussion of the structure and content of the spooling area.
SEE ALSO
hylafax-server(5), faxgetty(8)
July 17, 1995 FAXSTATE(8)