10 More Discussions You Might Find Interesting
1. AIX
We have an IBM Power 710. It has a USB port on the front. I have done some searching and see that there is information out there on how to create a JFS2 file system on USB drives. A few have commented that they would not recommend it, if the server is important, may crash the server... Just... (0 Replies)
Discussion started by: mbenedi
0 Replies
2. UNIX for Dummies Questions & Answers
Hi Guys,
Can any one help me on this.
I need help to move .csv/.xls file from unix path to windows shared drive or c:\ drive?
Regards,
LKR (1 Reply)
Discussion started by: lakshmanraok117
1 Replies
3. UNIX for Dummies Questions & Answers
I have recently installed UNIX SysV on an old computer to try and expand my general knowledge of computers. I want to install NASM on it so I can begin working on some assembly language, but I am having trouble accessing the floppy disk with the files I need.
I've tried running
mount /dev/fd0... (23 Replies)
Discussion started by: BrentBANKS
23 Replies
4. Solaris
Hi Guys,
I want to take backup of a ZFS file system on tape drive.
Can anybody help me with this?
Thanks,
Pras (0 Replies)
Discussion started by: prashant2507198
0 Replies
5. HP-UX
Hi,
I have a problem again and I hope that someone on this forum will help me in solving it. My English is weak, but I'll try to describe it clearly.
I have an old computer ( HP B180) with HP-UX 10.20. I've done the hard disk image using G4L and replaced the drive. Old drive has 4.3 GB and 9.1... (7 Replies)
Discussion started by: ftwojtek
7 Replies
6. UNIX for Advanced & Expert Users
Hi everyone!
A very frustrating night!!! I installed a new linux server on my system that has IDE drives and SATA drives. At the time of installation I only had IDE drive plugged in and that is where I install the linux. Everything works fine until I shut the system down and plug in my SATA... (3 Replies)
Discussion started by: hytron
3 Replies
7. Hardware
I have a 320 GB drive which dual boots Windows and Debian:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal):... (0 Replies)
Discussion started by: phillipsoasis
0 Replies
8. Linux
Hello sir,
I am Vijay Manohar. I am a writing a device driver for LCD frame buffer device. In this , LCD has been mapped at physical address 0x3000000. Now I want to implement mmap entry point. I have two questions regarding this
Can I use this physical address as one of the parameters to... (0 Replies)
Discussion started by: VijayManohar
0 Replies
9. Filesystems, Disks and Memory
I'm setting up a server with software RAID1, and everything is working perfectly, except that when I pull either of the drives, the system completely hangs and has to be rebooted. The computer is a Tyan Transport GX28, which is alleged to have hot-swappable SATA. I can fail a drive and the system... (1 Reply)
Discussion started by: vertigo23
1 Replies
10. UNIX for Dummies Questions & Answers
I have two unix workstations. One crashed :( , but the other is still operating efficiently. We have a Lacie external hard drive attached to the workstation that failed. I would like to mount the external drive to the workstation that is still functioning. I am not very familiar with how to do... (1 Reply)
Discussion started by: Tmarsha6
1 Replies
MLXCTL(8) BSD System Manager's Manual MLXCTL(8)
NAME
mlxctl -- Mylex DAC960 family management utility
SYNOPSIS
mlxctl [-f dev] [-v] [-a] status [drive] [...]
mlxctl [-f dev] [-a] detach [drive] [...]
mlxctl [-f dev] [-a] check [drive] [...]
mlxctl [-f dev] rebuild channel:target
mlxctl [-f dev] cstatus
mlxctl [-f dev] rescan
mlxctl [-f dev] config
DESCRIPTION
The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.
The following options are available:
-a Apply the action to all drives attached to the controller.
-f dev Specify the control device to use. The default is /dev/mlx0.
-v Increased verbosity.
The following commands are available:
cstatus Display the controller's current status.
status Display the status of the specified drives. This command returns 0 if all drives tested are online, 1 if one or more drives are
critical and 2 if one or more are offline.
rescan Re-scan the logical drive table, and attach or detach devices from the system as necessary.
detach Detach the specified drives. Drives must be unmounted and unopened for this command to succeed.
check Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5). This command returns imme-
diately. The status command can be used to monitor the progress of the check.
rebuild Rebuild onto the specified physical drive. Note that there can be only one running rebuild operation per controller at any given
time. This command returns immediately. The cstatus command can be used to monitor the progress of the rebuild.
config Write the current system drive configuration to stdout.
EXAMPLES
Display the status of drive ld3 attached to the controller mlx1:
mlxctl -f /dev/mlx1 -v status ld3
SEE ALSO
ld(4), mlx(4)
HISTORY
The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.
BUGS
Modifying drive configuration is not yet supported.
Some commands do not work with older firmware revisions.
Error log extraction is not yet supported.
BSD
April 10, 2000 BSD